AMPROBE

Amprobe AMP-210 600A AC TRMS Clamp MeterWith a full range of AC current, AC/DC voltage, and frequency measurement functions for basic electrical troubleshooting, the AMP-210 clamp meter with its large backlit display is an excellent amp clamp meter choice. Rated CAT III 600 V, the AMP-210 clamp meter offers True-RMS sensing, fast response processor, non-contact voltage detection, capacitance, resistance and continuity measurements to enhance efficiency and safety in today’s complex electrical environments. The Amp-Tip function allows for precise measurement of current down to the tenth of an Amp, enabling accurate current measurement of both large and small diameter wires. A low pass filter allows measurement of current and voltage on variable frequency drives (motors with speed controlled by frequency).FEATURESMeasures AC Current to 600 A and AC/DC Voltage to 600 VFeatures True-RMS sensing for accurate voltage measurements in noisy electrical environmentsAmp-Tip delivers precise low AC current measurements – 0 to 60 AIncludes a low pass filter to accurately measure voltage and current on variable frequency drivesCapacitance measurement, continuity beeper and diode testProvides resistance and continuity measurement capabilities to verify the quality of electrical connections and the proper operation of motor and transformer coilsOffers data hold and relative zero for quick analysisMaximizes battery life with auto power off and low battery indicatorBacklit display for easy measurement viewing in bright and dim environmentsAccommodates conductors up to 1.18 in (30mm)Includes test leads, batteries (installed), carrying case, and user manualCAT III 600 V safety ratedSPEIFICATIONFEATUREAMP-210AMP-220AMP-310AMP-320AMP-330AC voltage (True-rms)Range:0 to 600.0 V0 to 1000.0 VAccuracy:±1.0% + 5LSD (50 to 60 Hz)±0.8% + 5LSD (50 to 60 Hz)DC voltageRange:0 to 600.0 VAccuracy:±1.0% + 5LSDAC+DC voltageRange:–0 to 600.0 V–0 to 600.0 V0 to 1000.0 VAccuracy:–±1.2% + 7LSD (50 to 60 Hz)–±1.2% + 7LSD (50 to 60 Hz)±1.0% + 7LSD (50 to 60 Hz) ±1.8% + 7LSD (DC 40 to 200 Hz) ±1.2% + 7LSD 200 to 400 Hz)AC currentRange:0 to 600.0 AAccuracy:±1.8% + 5LSD (50 to 60 Hz) ±2.0% + 5LSD (100 to 400 Hz)DC currentRange:–0 to 600.0 A–0 to 600.0 A0 to 1000.0 AAccuracy:–±2.0% + 5LSD (DC 50 to 100 Hz)–±2.0% + 5LSD (DC 50 to 100 Hz)±1.8% + 5LSD (DC 50 to 100 Hz)AC+DC currentRange:–0 to 600.0 A–0 to 600.0 A0 to 1000.0 AAccuracy:–±2.2% + 7LSD (DC 50 to 100 Hz) ±2.7% + 7LSD (100 to 400 Hz)–±2.2% + 7LSD (DC 50 to 100 Hz) ±2.7% + 7LSD (100 to 400 Hz)±2.2% + 7LSD (40 to 100 Hz) ±2.5% + 7LSD (100 to 400 Hz)Precise low current ACRange:0 to 60.00 AAccuracy:±1.5% + 5LSD (50 to 60 Hz)±1.5% + 5LSD (50 to 60 Hz) ±2.0% + 5LSD (0.00 to 20.00 A, 100 to 400 Hz) ±3.0% + 5LSD (>20.00 to 60.00 A, 40 to 100 Hz) ±3.0% + 5LSD (>20.00 to 60.00 A, 100 to 100 Hz)Precise low current DCRange:–0 to 60.0 A–0 to 60.0 A0 to 60.00 AAccuracy:–±2.0% + 5LSD–±2.0% + 5LSD±1.5% + 5LSD (0.00 to 20.00 A) ±3.0% + 5LSD (>20.00 to 60.00 A)Micro ampsRange:––0 to 2000 µAAccuracy:––±1.0% + 5LSDFrequencyRange:5.00 to 999.9 HzAccuracy:±1.0% + 5LSD (600 V range)Range:50.0 to 400.0 HzAccuracy:±2.0% + 4LSD (600 A range)ResistanceRange:0.0 to 60.00 kΩAccuracy:±1.0% + 5LSDCapacitanceRange:0.0 to 2500 µFAccuracy:±2.0% + 4LSDContinuity beeperON ≤ 10 ΩOff > 250 ΩTemperature* (Type K thermocouple) ––-40.0 to 752 °F-40.0 to 400 °C ––±1.0% + 3.0 °F (-40.0 to 14.0 °F) ±1.0% + 1.5 °F (>40.0 to 99.9 °F) ±1.0% + 2.0 °F (100 to 752 °F) ±1.0% + 1.5 °C (-40.0 to 10.0 °C) ±1.0% + 0.8 °C (>-10.0 to 99.9 °C) ±1.0% + 1.0 °C (100 to 400 °C) Non-contact voltage10 V to 1000 V AC (50 to 60 Hz)Phase rotation indication ––Rotation-R for main supply Rotation-M for motorsDiode test •••••Jaw opening 1.18 in (30 mm)1.37 in (35 mm)1.18 in (30 mm)1.37 in (35 mm)2.0 in (51 mm)Safty rating CAT III 600 VCAT IV 600V CAT III 1000 VSpecial FeaturesIn-rush current –••••Peak hold (Crest) ––––•Relative zero •••••Max/Min/Avg •••••Data hold •••••Backlight •••••Auto power off •••••Work light ––––•Alat Laboratorium Umum

Amprobe INSP-3 Wiring Inspector Circuit TesterThe rugged Amprobe INSP-3 Wiring Inspector Circuit Tester verifies in seconds whether a building’s wiring (including voltage drop under load) complies with electrical code. This saves time and money by eliminating guess work. The large display shows all relevant test data so you can quickly identify issues with splices, connections, and conductor quality that are crucial to safety and performance, without scrolling or switching screens. Select a 10, 15, or 20 amp load on the electricity tester then read the results. A flashing screen clearly indicates incorrect wiring or failures. This wire tester won’t trip circuit breakers or blow fuses during the test.FEATURESPresents relevant test data (voltage, voltage drop, hot and neutral voltage drop, voltage with load, ground impedance) on a single large display to save operator time. No scrolling or switching screens neededVerifies that wiring tested for load carrying ability meets electrical code recommendations for voltage drop under loadDetects faulty wiring without removing outlets cover plates or panel coversFinds most common wiring problems, including:Faulty splices and connectionsIncorrect wiringUndersized wiringFaulty GFCIsFaulty or incorrectly wired AFCIsIncorrect line voltagePoor ground qualityFlashing screen clearly indicates incorrect wiring or voltage drop test failureOffers user-selectable 10, 15 and 20 amps load testing to verify electrical system performanceWill not trip circuit breakers or blow fuses during the testChecks grounding quality for safety and the ability to support sensitive electronic equipmentMeasures fault currentsTests GFCI and AFCI operationsIncludes power cord, 9V alkaline battery (Installed), users manual, and carrying case  SPECIFICATIONFEATUREINSP-3Best AccuracyLoad:Constant 10, 15 or 20 AMP simulation regardless of line voltage-Operating voltage:95 VAC → 120 VAC+/- 2 % + 2 digitsGFI trip:6.0 mA nominal to trip GFI, 30 mA to trip RCD-AFCI trip:Up to 8, 120 AMP pulses within 1/2 second period- SpecificationsLoad:Constant 0, 10, 15 or 20 AMP simulation regardless of line voltageOperating voltage:95-120 VAC +/-2%, +/- 2 digitsGFI trip:6.0 mA nominal to trip GFI, 30 mA to trip RCDAFCI trip:Up to 8, 120 AMP pulses within 1/2 second periodModel NameDescription INSP-3Testing efficiency - relevant test data (voltage, voltage drop, hot and neutral voltage drop, voltage with load, ground impedance) is presented on a single large display to save operator time - no scrolling or switching screens neededVerifies if wiring is tested for load carrying ability that it meets electrical code recommendations for voltage drop under loadIncluded Accessories:   Power cord,9 V alkaline battery (installed),users manual, carrying caseAlat Laboratorium Umum

Amprobe ALC-110 Leakage Current ClampOverviewPrevent unplanned downtime by detecting leakage currents with the ALC-110 Leakage Current Clamp. Rated CAT III 600 V to ensure electrical safety, the ALC-110 is designed to resist external magnetic fields for highly accurate readings. Features TRMS, a mechanical jaw lock, max readings and hold functions, highest resolution of 0.001 mA (measure up to 60 A), broad frequency range (15 Hz to 1 kHz), selectable filters (low pass, appliance, no filter), selectable limits (0.25 mA, 0.5 mA, 3.5 mA, 10 mA, 12 mA) and a battery-saving design.Use the ALC-110 to:MeasureEarth and differential leakage currentsLeakage currents through the earth (PE) conductorAppliance current consumption without interruptions to the circuitTrace the source of earth leakage currentsIdentify intermittent GFCI trips without switching equipment offCheck a system for an electrical break of insulation where current is flowing to the groundWhere industrial leakage current testing is requiredFeaturesLow frequency magnetic fields≤ 30 A/m, operating class 2 @ IN : 3.500 mA to 600.0 mA / 40 Hz to 1 kHzMeasurement categoryCAT III 600 VTrue-rmsYesAC frequency15 Hz to 1 kHzLow pass filter50 – 60 Hz, for appliance measuring acc. EN61557-16 amendment A, no filterLimit judgement0.25 mA, 0.5 mA, 3.5 mA, 10 mA, 12 mAJaw opening1.2 in (30 mm) max.Jaw lockingYesBacklight functionYesOverload protection60 AAuto power offIdle 20 minutesAuto rangingYesMax holdYesData holdYesComplies with IEC/EN 61557-13YesBuilt according IEC/EN 61010-2-032Yes General SpecificationsDisplayDigital: 6000 counts, updates 5/secRangeAuto rangingOver range indicationOL or -OLOperating temperature32 °F to 86 °F (0 °C to 30 °C), ≤ 80% RH86 °F to 104 °F (30 °C to 40 °C), ≤ 75% RH104 °F to 122 °F (40 °C to 50 °C), ≤ 45% RHOperating altitude≤ 2000 mStorage temperature-4 °F to 140 °F (-20 °C to 60 °C)Pollution degree2Temperature coefficient0.1 x (specified accuracy) / °C (<21 °C, <25 °C)Vibration requirementacc. IEC 61557-1 clause 4.10Drop proof4 ft (1.2 m)Battery2x batteries 1.5 V IEC LR03 AAABattery life60 hours typicalSafety complianceIEC/EN 61010-1, IEC/EN 61010-2-030, IEC/EN 61010-2-032, IEC/EN 61557-13EMC complianceIEC/EN 61326-1, IEC/EN 61326-2-2Dimensions (H x W x L)8.7 x 3.5 x 1.8 in (221 x 89 x 48 mm)Weight0.9 lb (410 g) with batteries installed   Model NameDescription ALC-110Amprobe ALC-110 Leakage Current ClampDescription: Leakage Current ClampIncluded Accessories: 2 x AAA batteries, soft carrying case and user manual Clamp Meter

Amprobe AT-6010 Advanced Wire Tracer KitEasily and accurately locate wires, breakers, and fuses with the AT-6010 Advanced Wire Tracer. When the Transmitter is connected to the circuit (Energized or De-energized, up to 600 V AC/DC in Category I through Category III electrical environments), the Receiver easily detects the transmitted signal in the wires or cables behind walls, ceilings and floors. Work safely on energized circuits without the need to take equipment offline. The Transmitter also features high signal mode for general tracing and a loop mode designed specifically for locating shorts, as well as two optimal tracing frequencies that are automatically activated based on the detected voltage. The AT-6010 can be combined with the CT-400 Signal Clamp (optional accessory) for applications where access to circuit contacts is limited or where users are not able to connect the Transmitter to the circuit through test leads.FEATURESTraces wires in walls, ceilings, floors and cornersLocates breakers and fusesPinpoints shorts and opensHigh resolution 2.5"" TFT LCD black & white displaySimple one button Transmitter operationTwo Transmitter signal modes"High Signal" mode for normal circuits"Loop" mode for closed loop de-energized circuitsTwo automatically selected frequency modes for reliable tracing on energized and de-energized circuitsComes with custom Amprobe soft carrying case, test leads and accessoriesRated CAT III 600 V for work directly on an energized circuit without the need to take equipment offlineCompatible with optional Signal Clamp (CT-400) clamp-on attachmentSPECIFICATIONFeaturesAT-6010-R ReceiverAT-6010-T TransmitterMeasurement categoryCAT III 600 VOperating voltage/current0 to 600 VOperating frequencyEnergized: 6.25 kHzHazardous voltage detectionN/A> 30 V AC/DCSignal indicationsNumeric bar graph display and audible beepLEDsResponse timeTip Sensor (Energized/De-energized): 500 msBattery voltage monitoring: 5 secLine voltage monitoring: 1 secBattery voltage monitoring: 5 secCurrent output of signal (typical)N/AEnergized circuit:HI mode: 60 mA RMSDe-energized circuit:HI mode: 130 mA RMSLoop mode: 160 mA RMSSignal voltage output (nominal)N/ADe-energized circuit:HIGH: 33 V RMS, 140 Vp-pWith CT-400:Loop model:31 V RMS, 120 Vp-pRange detection (open air)Tip Sensor (Energized):Max distance via air: up to 20 ft (6.1 m)Pinpointing: approx. 1.97 in (5 cm)Tip Sensor (De-energized):Max distance via air: up to 14.7 ft (4.5 m)Pinpointing: approx. 1.97 in (5 cm)N/ADisplay sizeLCD 2.5 in (6.35 cm)N/ADisplay dimensions (W x H)1.45 x 1.93 in(36.72 x 48.96 mm)N/ADisplay typeSegment LCDLEDsDisplay colorBlack and whiteOperating mode LEDs: redBattery status LED: redBooting time< 3 sec< 2 secBacklightYesN/AOperating temperature-4 °F to 122 °F (-20 °C to 50 °C)Operating humidity45%: -4 °F to <50 °F (-20 °C to <10 °C)95%: 50 °F to <86 °F (10 °C to <30 °C)75%: 86 °F to <104 °F (30 °C to <40 °C)45%: 104 °F to 122 °F (40 °C to 50 °C)Storage temperature and humidity-4 °F to 158 °F (-20 °C to 70 °C), <95% RHOperating altitude0 to 6561 ft (2000 m)Transient protectionN/A6.00 kV (1.2/50μS surge)Pollution degree2IP ratingIP 52IP 40Drop test3.28 ft (1 m)Power supply4 x AA (alkaline)8 x AA (alkaline)Power consumption (typical)70 mAHi mode: 70 mALoop mode with Clamp: 90 mAConsumption without signal transmission: 10 mABattery lifeApprox. 25 hHi mode: approx. 25 hLoop mode: approx. 18 hLow battery indicationYesFuseN/A1.6 A, 700 V, fast-acting,Ø 6x32mmDimensions (L x W x H)Approx. 7.2 x 2.95 x 1.69 in(183 x 75 x 43 mm)Approx. 7.2 x 3.66 x 1.97 in(183 x 93 x 50 mm)WeightApprox. 0.6 lb (0.27 kg)Approx. 1.25 lb (0.57 kg)Certifications Refer to user manual for accessory specifications Kit ContainsAT-6010AT-6010-R Receiver•AT-6010-T Transmitter•TL-6000-INTL Test lead and accessory kit*•CC-6010 Soft carrying case•User Manual•Quick Reference Guide•1.5 V AA (IEC LR6) Battery12* TL-6000-INTL test lead and accessory kit includes:2 x 1 m test leads (red, black)1 x 7 m test lead (green)2 x Alligator clips (red, black)2 x Outlet blade adapter (red, black)2 x Outlet round adapter (red, black) Optional AccessoriesADPTR-SCT Socket adapterHS-1 Magnetic hangerTL-7000-25M Test leadCT-400 Signal clamp  Model NameDescription AT-6010Amprobe AT-6010 Advanced Wire Tracer KitIncluded Accessories: AT-6010-R Receiver, AT-6010-T Transmitter, CC-6010 Soft Carrying Case, TL-6000-INTL Test Lead and Accessory Kit (2 x 1 m test leads, 1 x 7 m test lead, 2 x alligator clips, 2 x outlet blade adapters, 2 x outlet round adapters), 12 x AA Batteries, User Manual, Quick Reference Guide  Model and AccessoriesTest Leads AMP TL-6000-INTLUse the TL-6000-INTL Test Lead and Accessory Kit with the AT-6010 Advanced Wire Tracer. Included Accessories: 2 x 1 m test leads, 1 x 7 m test lead, 2 x alligator clips, 2 x outlet blade adapters, 2 x outlet round adapters  Clamp on Attachments AMP CT-400Experience this signal clamp from Amprobe. Use the CT-400 Signal Clamp with the AT-6000-T to induce signal into wires when there is no access to bare conductors.  Other HS-1Experience this hanging strap accessory from Amprobe. Use the HS-1 to hang, place on your belt or stand up your digital multimeter or Advanced Wire Tracer Transmitter. AMP ADPTR-SCTAmprobe Socket-Check Adapter Included Accessories: User Manual Multimeter

Amprobe MT-10 Moisture MeterMeasure moisture content for wall board, wood or other building materials to determine places of harmful mold growth or unseen water damage.Typical application also include checking moisture of concrete slab and wood before installation of floors, determining wood moisture content during drying process, and checking wood moisture before material is used for woodworking applications.FeaturesChecks for moisture content in wood, paper or cardboard and building materials such as sheetrock, concrete, mortar, plaster, etc.Measurement ranges: Wood/ Paper: 8 ~ 60%Building material: 0.3 - 2.0% Temperature: 0°C ~ 40°C or 32°F ~ 99°FUsed in indoor air quality applications for detecting moisture in the walls, floors and ceilings stimulating mold growthLCD display provides moisture or temperature measurementThree color LED provides quick moisture indication:Green - “air-dry conditionsYellow - increased moistureRed - excess moistureBacklight for operation in dark areasLow battery indicationAuto power off  SPECIFICATIONMeasurement range:-Wood:8 ~ 60%Building material:0.3-2.0%Temperature:0 ~ 40°C or 32 ~ 99°FResolution:-Wood:0.10%Building material:0.01%Temperature:0.1°C / 0.2°FAccuracy:-Wood:±2%Building material:±0.1%Temperature:±1°C / ±2°FBattery:9V, 6F22 Model NameDescriptionMT-10Checks for moisture content in wood, paper or cardboard and building materials such as sheetrock, concrete, mortar, plaster etc…Measurement Ranges: Wood/ Paper: 8 ~ 60% Building Material: 0.3 - 2.0% Temperature: 0°C ~ 40°C or 32°F ~ 99°FIncluded Accessories:Users manual, battery Moisture Meter

Alat Laboratorium UmumBATTERY TESTERFeaturesEasy-to-read color-coded display with “good,“low and “replace/recharge indicatorsWorks with standard and rechargeable batteriesCompatible with: 9V, AA, AAA, C, D, 1.5V button typeCompact designErgonomic battery holderUsers manual included