RIGOL

Rigol DP832 Triple Output 195 Watt Power SupplyThe Rigol DP832 is a very high-quality programmable laboratory power supply with three switchable outputs (+30 V/3 A, +30 V/3 A and +5 V/3 A) and a maximum power output of 195 W.Like all Rigol devices, the power supply features a very well constructed and easy to use interface offering comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.The Rigol DP832 features a relatively large (8.9 cm / 3.5") and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.The DP800 Series Power Supplies combine the ability to source, analyze, and coordinate over time in a powerful new package. The DP800 Series is a family of linear power supplies systems with 3 outputs and up to 195 Watts in total. With one channel isolated, users can reconfigure instruments into any number of systems or applications.Built in V, A, and W measurements make power monitoring easy, but additional wave tracking, timing, and analysis features mean there are even more ways to use the supplies. New digital triggering between instruments also makes it possible to reliably combine and connect supplies together. Intuitive to use for everything from education labs to the R & D bench, the DP800 family of power supplies provide incredible value for any application.Typical ApplicationsR&D Lab general purpose testingQuality Assessment inspectionBias power for RF/MW circuitsAutomotive electronic testProduction testingDevice or circuit characterization and troubleshooting RIGOL DP800 SERIES SPECIFICATIONSModelDP832ADP832DP831ADP811ADP821AChannels312DC Output (0°C to 40°C )     Voltage/currentCH1: 0 to 30V/0 to 3ACH2: 0 to 30V/0 to 3ACH3: 0 to 5V/0 to 3ACH1: 0 to 8V/0 to 5ACH2: 0 to +30V/0 to 2ACH3: 0 to -30V/0 to 2A0 to 20 V/ 0 to 10 A (Low Range) or 0 to 40 V/0 to 5 A (High Range)CH1: 0 to 8 V0 to 10 ACH2: 0 to 60 V0 to 1 A OVP/OCPCH1: 1mV to 33V/1mA to 3.3ACH2: 1mV to 33V/1mA to 3.3ACH3: 1mV to 5.5V/1mA to 3.3ACH1: 10mV~33V/1mA~3.3ACH2: 10mV~33V/1mA~3.3ACH3: 10mV~5.5V/1mA~3.3ACH1:1mV ~ 8.8V/0.1mA ~ 5.5ACH2:1mV ~ 33V/0.1mA ~ 2.2ACH3:-1mV ~ -33V/0.1mA ~ 2.2A0.1 V to 22 V or0.1 V to 44 VCH1: 0.1 to 8.8 V0.1A to 10.5A CH2: 0.1 to 66 V0.1A to 1.1A Load Regulation Rate ±(Output Percentage + Offset)  Voltage<0.01%+2mVCurrent<0.01%+250uALinear Regulation Rate ±(Output Percentage + Offset)  Voltage<0.01%+2mVCurrent<0.01%+250uARipples and Noise (20Hz to 20MHz)  Normal Mode Voltage<350μVrms/2mVppNormal Mode Current<2mArmsCommon Mode Current<1.5μArmsNot specifiedAnnual Accuracy [1] (25°C ±5°C ) ±(Output Percentage + Offset)  ProgrammingVoltage0.05% + 10mV0.15%+ 5mA0.05% + 10mVCH1: 0.05% + 10mVCH2: 0.1% + 25mVCurrent0.2% + 10mA0.2%+10mA0.1% + 10mA0.2% + 10mAReadbackVoltage0.05% + 5mV0.1%+20mV0.05% + 10mVCH1: 0.05% + 5mVCH2: 0.1% + 25mVCurrent0.15%+ 5mA0.2%+10mA0.1% + 10mA0.15% + 10mAResolution  ProgrammingVoltage1mV10mVWith high-resolution option:1mV1mV1mVCH1: 1 mVCH2: 10 mV Current1mA1mACH1: 0.3mACH2/CH3: 0.1mA0.5mACH1: 1 mACH2: 0.1 mAReadbackVoltage0.1mV10mVWith high-resolution option:0.1mV0.1mV0.1mVCH1: 1 mVCH2: 1 mV Current0.1mA1mAWith high-resolution option:0.1mA0.1mA0.1mACH1: 1 mACH2: 0.1 mADisplayVoltage1mV10mVWith high-resolution option:1mV1mV1mVCH1: 1 mVCH2: 10 mV Current1mA10mAWith high-resolution option:1mA1mA1mACH1: 1 mACH2: 0.1 mATransient Response Time  Less than 50μs for output to recover to within 15mV following a change in output current from full load to half load or vice versa.Command Processing Time [2]  <100msTemperature Coefficient per? (Output Percentage + Offset)     VoltageCH1/CH2: 0.01%+5mVCH3: 0.01%+2mV0.01%+2mV0.01%+3mVCurrent0.01%+2mA0.02%+3mA0.02%+3mAStability [3] ±(Output Percentage + Offset)  VoltageCH1/CH2: 0.02%+2mVCH3: 0.01%+1mVCH1: 0.03%+1mVCH2/CH3: 0.02% + 2mV0.02%+1mVCurrent0.05%+2mACH1: 0.1%+3mACH2/CH3: 0.05% + 1mA0.1%+1mATech SpecsPower Supplies/DC Power Supplies TemplateOutputsTripleVoltage Output 1VariableMax Voltage Output 130 VMin Voltage Output 10 VProgrammableYesCurrent Output 1VariableMax Current Output 13 AMin Current Output 10 AVoltage Output 2VariableMax Voltage Output 230 VMin Voltage Output 20 VCurrent Output 2VariableMax Current Output 23 AMin Current Output 20 AVoltage Output 3VariableMax Voltage Output 35 VMin Voltage Output 30 VCurrent Output 3VariableMin Current Output 30 AMax Current Output 33 AMeter TypeDigitalLinear/SwitchingLinearMax Display Resolution Current10 mAMax Display Resolution Voltage10 mVConstant current/voltageYesRemote SensingNoTest Equipment General AttributesUnique FeaturesLow Ripple Noise: <350 uVrms/2mVppFast Transient Response Time: <50usChannel isolation: CH1 || CH2,CH3Standard OVP/OCP/OTP protection functionsStandard Timing functionBuilt in V,A,W measurements and waveform displaySupport Output Delay, Analysis, Monitor, Preset functionsIndependent control for each channel3.5 Inch TFT DisplayWarranty3 YEARS Oscilloscopes

Rigol DS1054Z Digital Oscilloscope 50 MHz DSO 4 ChannelsBest Selling OscilloscopeFind out why the DS1054Z is one of the top selling oscilloscopes in the WORLD since its release in September 2014. Read the reviews! Let our customers tell you what they think of this unit. Schools, companies, students and home hobbyists love the DS1054Z. Backed by a 30 day money back guarantee you cannot go wrong with this unit.50 MHz Analog BandwidthTotal of 4 Analog ChannelsMaximum Waveform Capture Rate of up to 30,000 wfms/sIncludes 4 RP2200 150 MHz Passive HighZ ProbesLow noise floorUSB Host for Thumb DriveLarge 7" Display12 Mpts of Memory - upgradeable to 24 ImageModelDS1054ZDS1074Z PlusDS1074Z-S PlusDS1104Z PlusDS1104Z-S PlusAnalog Bandwidth50 MHz70 MHz100MHzDigital Connector Port for optional MSO KitNoYesYesChannels4Max. Sample rate1GSa/s (Single-channel),  500MSa/s(Dual-channel), 250MSa/s(Fulll-channel)Max. Memory Depth12Mpts(std.), 24Mpts(option)Max. Waveform Capture rateUp to 30,000 wfms/sReal Time waveform Record,Replay and Analysis functionUp to 60, 000 Frames(Opt.)Std. ProbesRP2200 150MHz BW Passive Probe:4 setsBuilt in 2 Ch SourceNoNoYesNoYes SampleSample ModeReal-time SampleReal-time Sample Rate1 GSa/s (single-channel)500 MSa/s (dual-channel)250 MSa/s (four-channel)Peak Detect4 nsAveragingAfter both the channels finish N samples at the same time, N can be 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024.High ResolutionThe highest resolution is 12 bitMemory DepthSingle-channel: Auto, 12k pts, 120k pts, 1.2M pts, 12M pts and 24M pts (option) are availableDual-channel: Auto, 6k pts, 60k pts, 600k pts, 6M pts and 12M pts (option) are availableFour-channel: Auto, 3k pts, 30k pts, 300k pts, 3M pts and 6M pts (option) are availableInputNumber of Channelsfour-channelInput CouplingDC, AC or GNDInput Impedance(1 MΩ±2%) || (13 pF±3 pF)ProbeAttenuationCoefficient0.01X-1000X, 1-2-5 stepMaximum Input Voltage (1MΩ) Maximum input voltage of the analog channelCAT I 300 Vrms, CAT II 100 Vrms, transient overvoltage 1000 VpkWith RP2200 10:1 probe: CAT II 300 VrmsHorizontalTime Base Scale5 ns/div to 50 s/divTime Base Accuracy [1]≤ ± 25 ppmTime Base Drift≤ ± 5 ppm/YearDelay RangePre-trigger (negative delay): ≥1 screen widthPost-trigger (positive delay): 1 s to 100,000 sTime Base ModeY-T, X-Y, Roll, DelayedNumber of X-Ys1 pathWaveform Capture Rate [2]30,000 wfms/s (dots display)VerticalBandwidth (-3dB)DS1104Z: DC to 100 MHzDS1074Z: DC to 70 MHzSingle BandwidthDS1104Z: DC to 100 MHzDS1074Z: DC to 70 MHzVertical Resolution8 bitVertical Scale1 mV/div to 10 V/divOffset Range1 mV/div to 499 mV/div: ± 2 V500 mV/div to 10 V/div: ± 100 VBandwidth Limit120 MHzLow Frequency Response(AC coupling, -3dB)≤5 Hz (on BNC)Rise Time [1]DS1104Z: 3.5 nsDS1074Z: 5 nsDC Gain Accuracy [3]<10 mV: ±4% full scale≥10 mV: ±3% full scaleDC Offset Accuracy±0.1 div ± 2 mV ± 1% offsetChannel to ChannelIsolationDC to maximum bandwidth: >40 dBTriggerTrigger Level Range±5 div from the center of the screenTrigger ModeAuto, Normal, SingleHoldoff Range16 ns to 10 sHigh FrequencyRejection275 kHzLow FrequencyRejection275 kHzTrigger Sensitivity [1]1.0div (below 5mV or noise rejection is enabled)0.3div (above 5mV and noise rejection is disabled)Edge TriggerEdge TypeRising, Falling, Rising&FallingPulse TriggerPulse ConditionPositive Pulse Width (greater than, lower than, within specified interval)Negative Pulse Width (greater than, lower than, within specified interval)Pulse Width Range8 ns to 10 sRunt TriggerPulse ConditionNone, > (greater than), < (lower than), <> (within the specified interval)PolarityPositive, NegativePulse Width Range8 ns to 4 sWindows Trigger Windows TypeRising, Falling, Rising&FallingTrigger PositionEnter, Exit, TimeWindows Time8 ns to 10 sNth Edge TriggerEdge TypeRising, FallingIdle Time16 ns to 10 sNumber of Edges1 to 65535Slope TriggerSlope ConditionPositive Slope (greater than, lower than, within specified interval)Negative Slope (greater than, lower than, within specified interval)Time Setting8 ns to 10 sVideo TriggerSignal StandardSupport standard NTSC, PAL and SECAM broadcasting standardsSupport 480P, 576P HDTV standardsPattern TriggerPattern SettingH, L, X, Rising Edge, Falling EdgeDelay TriggerEdge TypeRising, FallingDelay Type> (greater than), < (lower than), <> (within the specified interval), >< (outside the specified interval)Delay Time8 ns to 10 sTimeOut Trigger Edge TypeRising, Falling, Rising&FallingTimeOut Value16 ns to 10 sDuration Trigger Pattern SettingH, L, XTrigger Condition> (greater than), < (lower than), <> (within the specified interval)Duration Time8 ns to 10 sSetup/Hold Trigger Edge TypeRising, FallingData PatternH, L,XSetup Time8 ns to 1 sHold Time8 ns to 1 sRS232/UART TriggerPolarityNormal, InvertTrigger ConditionStart, Error, Check Error, DataBaud2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps, UserData Bits5 bits, 6 bits, 7 bits, 8 bitsI2C TriggerTrigger ConditionStart, Restart, Stop, Missing Ack, Address, Data, A&DAddress Bits7 bits, 8 bits, 10 bitsAddress Range0x0 to 0x7F, 0x0 to 0xFF, 0x0 to 0x3FFByte Length1 to 5SPI TriggerTrigger ConditionTimeOut, CSTimeout Value16 ns to 10 sData Bits4 bit to 32 bitData Line SettingH, L, XMeasureManual mode | Voltage deviation between cursors (ΔV)Time deviation between cursors (ΔT)Reciprocal of ΔT (Hz) (1/ΔT)Track mode | Voltage and time values of the waveform pointAuto mode | Allow to display cursors during auto measurementAuto MeasurementMeasurements of Maximum, Minimum,Peak-Peak Value, Top Value, Bottom Value,Amplitude, Average, Mean Square Root,Overshoot, Pre-shoot, Frequency, Period, RiseTime, Fall Time, Positive Pulse Width, NegativePulse Width, Positive Duty Cycle, NegativeDuty Cycle, Delay A~B , Delay A~B , PhaseA~B , Phase A~BNumber ofMeasurementsDisplay 5 measurements at the same timeMeasurementRangeScreen Region or Cursor RegionMeasurementStatisticCounterAverage, Max, Min, Standard DeviationNumber of MeasurementsHardware 6 bits counter (channels areselectable)MathWaveformA+B, A-B, A×B, A/B, FFT, &&, ||, ^, !, intg, diff, sqrt, lg, ln, exp, absFFT WindowRectangle, Hanning, Blackman, Hamming,Flat Top,TriangleFFT DisplaySplit, Full ScreenFFT Vertical ScaledB/dBm, VrmsNumber of Busesfor Decoding2Decoding TypeParallel (standard), RS232/UART (option), I2C (option), SPI (option)DisplayDisplay Type7.0 inches TFT LCD displayDisplay Resolution800 horizontal×RGB×480 vertical pixelDisplay Color160,000 Color (TBD)Persistence TimeMin, 50 ms, 100 ms, 200 ms, 500 ms, 1 s, 2 s, 5 s, 10 s, 20 s, InfiniteDisplay TypeDots, VectorsI/OStandard PortsUSB HOST, USB DEVICE, LAN, Aux (TrigOut /PassFail)Signal Sourse (DS1000Z-S) Number of Channels 2Sample Rate 200 MSa/sVertical Resolution 14 bitsHighest  Frequency 25 MHzStandard Waveform Sine, Square, Pulse, Triangle, Noise, DCArbitrary Waveform Since, Exp.Rise, EXP.Fall, ECG, Gauss, Lorentz, HaversineSine Frequency Range 0.1 Hz to 25 MHz Flatness ±0.5 dB (relative to 1 kHz) Harmonic Distortion -40 dBc Stray (Non-Harmonic) -40 dBc Total Harmonic Distortion 1% Signal-to-Noise ration 40 dBSquare/Pulse Frequency Range 0.1 Hz to 15 MHz Rise/Fall time <15 ns Overshoot <5% Duty Cycle 10% to 90% Duty Cycle  Resolution 1% to 10 ns (select the greater one) Minimum Pulse Width 20 ns Pulse Width Resolution 10 ns or 5 bits (select the greater one) Jitter 500 psTriangle Frequency Range 0.1 Hz to 100 kHz Linearity 1% Symmetry 0 to 100%Noise [1] Bandwidth25 MHzInternal Generatedwaveforms Frequency Range 0.1 Hz to 1 MHzArbitrary Waveforms Frequency Range 0.1 Hz to 10 MHz Waveform Length 2 to 16k ptsFrequency Accuracy100 ppm (lower than 10 kHz)50 ppm (greater than 10 kHz) Resolution 0.1 Hz or 4 bit, select the greater oneAmplitude Output Range 20 mVpp to 5 Vpp, High-resistance10 mVpp to 2.5 Vpp, 50 Ω Resolution 100 μV or 3 bit, select the greater one Accuracy 2% (1 kHz)DC Offset Range ±2.5 V, High-resistance±1.25 V, 50 Ω Resolution 100 μV or 3 bit, select the greater one Accuracy 2% (1 kHz)General SpecificationsProbe Compensation OutputOutput Voltage [1]About 3 V, peak-peakFrequency [1]1 kHzPowerPower Voltage100-240 V, 45-440 HzPowerMaximum 50 WFuse2 A, T degree, 250 VEnvironmentTemperature RangeIn operation: 0°C to +50°COut of operation: -40°C to +70°CCooling MethodFanHumidity Range0° to +30°C : ≤95°C relative humidity+35°C to +40°C : ≤75°C relative humidity+40°C to +50°C : ≤45°C relative humidityAltitudeIn operation: under 3,000 metersOut of operation: under 15,000 metersMechanicalDimensions [4]Width×Height×Depth =313.1 mm× 160.8 mm×122.4 mmWeight [4]Without package | 3.2 kg ± 0.2 kgWith package | 3.8 kg ± 0.5 kgAdjustment Interval The recommended calibration interval is one year.Regulation StandardsElectromagnetic2004/108/ECCompatibilityExecution standard EN 61326-1:2006 EN61326-2-1:2006SafetyUL 61010-1:2004; CAN/CSA-C22.2 NO.61010-1-2004;EN 61010-1:2001; IEC 61010-1:2001Oscilloscopes

Rigol DG822 - 25 MHz Function / Arbitrary Waveform Generator, 2 Channel25 MHz, two channel function generator2 Mpts memory depth (upgradeable to 8 Mpts)160 built-in arbitrary waveformsSample rate up to 125 MSa/sVarious modulation functions - AM, FM, PM, ASK, FSK, PSK, and PWMThe Rigol DG811 is a 10 MHz, single channel function generator which incorporates multiple instruments into one portable and cost effective device. The DG811 features 2 Mpts standard memory, which is upgradeable to 8 Mpts via software. In addition, the DG811 can be upgraded from a one channel to two channel instrument, simply by entering a keycode. Enabling the second channel does not cause any compromise in performance, and the unit would function equivalent to two independent signal sources.The DG811 is a multi-function instrument - function generator, arbitrary waveform generator, noise generator, pulse generator, harmonic generator, analog/digital modulator, and frequency counter. It offers high performance at an unprecedented price point, and is ideal for applications including education, R&D, and much more. DG800 Series SpecificationsModelDG812DG811DG822DG821DG832DG831Channel212121Max. Frequency10 MHz25 MHz35 MHzSample Rate125 MSa/sWaveformBasic WaveformsSine, Square, Ramp, Pulse, Noise, DC, Dual-toneAdvanced WaveformsPRBS, RS232, SequenceBuilt-in Arbitrary Waveforms160 types of waveforms, including Sinc, Exponential Rise, Exponential Fall, ECG, Gauss, HaverSine, Lorentz, etc. Frequency CharacteristicsSine1 μHz to 10 MHz1 μHz to 25 MHz1 μHz to 35 MHzSquare1 μHz to 5 MHz1 μHz to 10 MHz1 μHz to 10 MHzRamp1 μHz to 200 kHz1 μHz to 500 kHz1 μHz to 1 MHzPulse1 μHz to 5 MHz1 μHz to 10 MHz1 μHz to 10 MHzHarmonic1 μHz to 5 MHz1 μHz to 10 MHz1 μHz to 15 MHzPRBS2 kbps to 10 Mbps2 kbps to 20 Mbps2 kbps to 30 MbpsDual-tone1 μHz to 10 MHz1 μHz to 20 MHz1 μHz to 20 MHzRS232baud rate range: 9600, 14400, 19200, 38400, 57600, 115200, 128000, 230400Sequence2 k to 30 MSa/sNoise (-3 dB)100 MHz bandwidthArbitrary Waveform1 μHz to 5 MHz1 μHz to 10 MHz1 μHz to 10 MHzResolution1 μHzAccuracy±(1 ppm of the setting value + 10 pHz), 18℃ to 28℃Tech SpecsGenerators / Counters/Function Generator TemplateChannels2Frequency Maximum25 MHzFrequency Minimum1 uHz (0.000001 Hz)FunctionsBurst, CMOS, Noise, Other, Pulse, Ramp, Sine, Square, Sweep, Triangle, TTLMax Amplitude Vpp @ 50 ohms10 VArbitraryYesSample Rate125 MSa/SScreen TypeTFTColor ScreenYesDigital Amplitude Resolution16 BitsTriggeringYesCounter that displays frequency on screen.YesModulation TypesAM, FM, FSK, PSK, PWMGraphical DisplayYesMemory2 MP [megapoints] (2048 kB)Direct Digital Synthesis (DDS)NoPC BasedNoTest Equipment General AttributesUnique Features-16 Bit Resolution on All Models-Intuitive Next Generation Touch Interface-10MHz to 35MHz Frequency Ranges-Fanless Cooling for silent operation-High Sample Rate and Long Memory-Advanced Capabilities like Dual-Tone, Harmonics and Sequencing-Complex Integrated Functions like PRBS Patterns and RS232 Generation-Enhanced Waveform modes and Signal Fidelity with SiFi II technologyWarranty3 YEARSPengukur Elektronik Lainnya

Rigol PA1011 Power Amplifier 10WPA1011 10W Power AmplifierFor Waveform GeneratorsEasily  control the amplifier settings from the front panel of a RIGOL Arbitrary Waveform Generator Enables to set the Gain (x1 or x10), Polarity (Invert or Normal), Output  offset  and  the  output  status  in  connection  with  its software;     Up to 50kΩ output impedance; The integrated output protection circuit (overcurrent protection and  internal  temperature  abnormal  protection) provided  with ensures the instrument is working stably and safely; Compact size, easy to carry and use. Pengukur Elektronik Lainnya

Rigol DG1022Z 25 MHz Arbitrary Function Generator with Second ChannelDG1022Z 25 MHz Arbitrary Function Generator with second channelSiFi (Signal Fidelity) for 100% waveform replication2Mpts or 8Mpts/CH(std.), 16Mpts/CH (opt.) arbitrary waveform length Standard 2 full functional independent channels±1ppm frequency stability, -125dBc/Hz phase noise, 200ps low jitterBuilt-in 8 orders harmonics generatorBuilt-in 7 digits/s counter up to 200MHz160 built-in pre-edited waveforms Intuitive arbitrary waveform editing softwareFull modulation supported: AM, FM, PM, ASK, FSK, PSK and PWMModelDG1022ZDG1032ZDG1062ZChannel222Maximum Frequency25MHz30MHz60MHzSample Rate200MSa/sWaveformsBasic waveformsSine, Square, Ramp, Pulse, NoiseBuilt-in ArbitraryWaveforms160 kinds, including Sinc, Exponential Rise, ExponentialFall, ECG, Gauss, HaverSine, Lorentz, Dual-Tone, etc.Frequency CharacteristicsSine1µHz to 25MHz1µHz to 30MHz1µHz to 60MHzSquare1µHz to 25MHz1µHz to 25MHz1µHz to 25MHzRamp1µHz to 500kHz1µHz to 500kHz1µHz to 1MHzPulse1µHz to 15MHz1µHz to 15MHz1µHz to 25MHzHarmonic1µHz to 10MHz1µHz to 10MHz1µHz to 20MHzNoise (-3dB)25MHzbandwidth30MHzbandwidth60MHzbandwidthArbitrary Waveform1µHz 10MHz1µHz to 10MHz1µHz to 20MHzResolution1µHzAccuracy±1ppm of the settings, 18°C to 28°CSine Wave Spectrum PurityHarmonic DistortionTypical (0dBm)DC-10MHz (included): <-65dBc10MHz-30MHz (included): <-55dBc30MHz-60MHz (included): <-50dBcTotal HarmonicDistortion<0.075% (10Hz-20kHz, 0dBm)Spurious(non-harmonic)Typical (0dBm)≤10MHz: <-70dBc>10MHz: <-70dBc+6dB/octavePhase NoiseTypical (0dBm, 10kHz deviation)10MHz: <-125dBc/HzSignal CharacteristicsSquareRise/Fall TimeTypical (1Vpp)<10nsOvershootTypical (100KHz, 1Vpp)≤5%Duty Cycle0.01% to 99.99%(limited by the current frequency setting)Non-symmetry1% of period+5nsJitter (rms)Typical (1MHz, 1Vpp, 50O)≤5MHz: 2ppm+200 ps>5MHz: 200psRampLinearity≤51% of peak output(typical, 1kHz, 1Vpp, 100% Symmetry)Symmetry0% to 100%PulsePulse Width16ns to 999.999 982 118ks(limited by the current frequency setting)Duty Cycle0.001% to 99.999%(limited by the current frequency setting)Leading/TrailingEdge Time≥10ns(limited by the current frequency and pulse width settings)OvershootTypical (1Vpp)≤5%Jitter (rms)Typical (1Vpp)≤5MHz: 2ppm+200ps>5MHz: 200psArbWaveform Length8pts to 2Mpts (16Mpts optional)8pts to 8Mpts (16Mpts optional)Vertical Resolution14bitsSample Rate200MSa/sMinimum Rise/FallTimeTypical (1Vpp)<10nsJitter (rms)  Typical (1Vpp)≤5MHz: 2ppm+200ps>5MHz: 200psEdit MethodEdit Points, Edit Block, Insert WaveformHarmonicHarmonic Order≤8Harmonic TypeEven, Odd, All, UserHarmonic Amplitudecan be set for all harmonicsHarmonic Phasecan be set for all harmonicsOutput CharacteristicsAmplitude (into 50 Ω)Range≤10MHz: 1.0mVpp to 10Vpp≤30MHz: 1.0mVpp to 5.0Vpp≤60MHz: 1.0mVpp to 2.5VppAccuracyTypical (1kHz Sine, 0V Offset, >10mVpp, Auto)±1% of setting ± 1mVFlatnessTypical (Sine 2.5Vpp)≤10MHz: ±0.1dB≤60MHz: ±0.2dBUnitsVpp, Vrms, dBmResolution0.1mVpp or 4digitsOffset (into 50 Ω)Range (Peak ac+dc)±5Vpk ac+dcAccuracy±(1% of setting+5mV+0.5% of amplitude)Waveform OutputImpedance50Ω (typical)ProtectionShort-circuit protection, automatically disable waveformoutput when overload occursModulation CharacteristicsModulation TypeAM, FM, PM, ASK, FSK, PSK, PWMAMCarrier WaveformSine, Square, Ramp, Arb (except DC)SourceInternal/ExternalModulating WaveformSine, Square, Ramp, Noise, ArbDepth0% to 120%Modulating Frequency2mHz to 1MHzFMCarrier WaveformSine, Square, Ramp, Arb (except DC)SourceInternal/ExternalModulating WaveformSine, Square, Ramp, Noise, ArbModulating Frequency2mHz to 1MHzPMCarrier WaveformSine, Square, Ramp, Arb (except DC)SourceInternal/ExternalModulating WaveformSine, Square, Ramp, Noise, ArbPhase Deviation0° to 360°Modulating Frequency2mHz to 1MHzASKCarrier WaveformSine, Square, Ramp, Arb (except DC)SourceInternal/ExternalModulating WaveformSquare with 50% duty cycleKey Frequency2mHz to 1MHzFSKCarrier WaveformSine, Square, Ramp, Arb (except DC)SourceInternal/ExternalModulating WaveformSquare with 50% duty cycleKey Frequency2mHz to 1MHzPSKCarrier WaveformSine, Square, Ramp, Arb (except DC)SourceInternal/ExternalModulating WaveformSquare with 50% duty cycleKey Frequency2mHz to 1MHzPWMCarrier WaveformPulseSourceInternal/ExternalModulatingWaveformsSine, Square, Ramp, Noise, ArbWidth Deviation0% to 100% of Pulse WidthModulating Frequency2mHz to 1MHz[Mod/Trig/FSK/Sync] InputInput Range75mVRMS to ±5Vac+dcInput Bandwidth50kHzInput Impedance10kΩBurst CharacteristicsCarrier WaveformSine, Square, Ramp, Pulse, Noise, Arb (except DC)Carrier Frequency2mHz to 25MHz2mHz to 30MHz2mHz to 60MHzBurst Count1 to 1,000,000 or InfiniteStart/Stop Phase0° to 360°, 0.1° resolutionInternal Period1µs to 500sGated SourceExternal TriggerTrigger SourceInternal, External or ManualTrigger Delay0ns to 100sSweep CharacteristicsCarrier WaveformSine, Square, Ramp, Arb (except DC)TypeLinear, Log or StepDirectionUp/DownStart/Stop FrequencyConsistent with the upper/lower limit of the frequency ofthe carrier waveformSweep Time1ms to 500sHold/Return Time0ms to 500sTrigger SourceInternal, External or ManualMarkFalling edge of the Sync signal (programmable)CounterFunctionFrequency, Period, Positive/Negative Pulse Width,Duty CycleFrequency Resolution7 digits/second (Gate Time =1s)Frequency Range1µHz to 200MHzPeriod MeasurementMeasurement Range5ns to 16 daysVoltage Range and Sensitivity (Not modulation signal)DC CouplingDC Offset Range±1.5Vdc1µHz to 100MHz50mVRMS to ±2.5Vac+dc100MHz to 200MHz100mVRMS to ±2.5Vac+dcAC Coupling1µHz to 100MHz50mVRMS to ±2.5Vpp100MHz to 200MHz100mVRMS to ±2.5VppPulse Width and Duty Cycle MeasurementFrequency/AmplitudeRange1µHz to 25MHz50mVRMS to±2.5Vac+dcDC CouplingPulse WidthMinimum≥20nsResolution5nsDuty CycleRange (Display)0% to 100%Input CharacteristicsInput Signal RangeBreakdown Voltage±7Vac+dcImpedance=1MΩInput AdjustmentCouplingACDCHF SuppressionON: input bandwidth=250kHz;OFF: input bandwidth=200MHzInput TriggerTrigger Level Range-2.5V to +2.5V>Trigger SensitivityRange0% (about 140mV hysteresisvoltage) to 100% (about 2mVhysteresis voltage)Gate TimeGateTime11.310msGateTime210.48msGateTime3166.7msGateTime41.342sGateTime510.73sGateTime6>10sTrigger CharacteristicsTrigger InputLevelTTL-compatibleSlopeRising or falling (optional)Pulse Width>100nsLatencySweep: <100ns (typical)Burst: <300ns (typical)Trigger OutputLevelTTL-compatiblePulse Width>60ns (typical)Maximum Frequency1MHzTwo-channel Characteristics - Phase OffsetRange0° to 360°Waveform PhaseResolution0.03°Clock ReferenceExternal Reference InputLock Range10MHz±50HzLevel250mVpp to 5VppLock Time<2sImpedance (typical)1kΩ , AC couplingInternal Reference OutputFrequency10MHz±50HzLevel3.3VppImpedance (typical)50Ω, AC couplingSync OutputLevelTTL-compatibleImpedance50Ω, nominal valueOvervoltage ProtectionOvervoltage protection will take effect once any of the following two conditions ismet:• The amplitude setting in the generator is greater than 2Vpp or the outputoffset is greater than |2V DC |, the input voltage is greater than±11.5×(1±5%)V (<10kHz).• The amplitude setting in the generator is lower than or equal to 2Vpp or theoutput offset is lower than or equal to |2V DC |, the input voltage is greater than±3.5×(1±5%)V (<10kHz).General SpecificationsPowerPower Voltage100V to 240V (45Hz to 440Hz)Power ConsumptionLess than 40WFuse250V, T3.15ADisplayType3-inch TFT LCDResolution320 Horizontal×RGB×240 Vertical ResolutionColor16M colorEnvironmentTemperature RangeOperating: 0ºC to 50ºCNon-Operating: -40ºC to 70ºCCooling MethodCooling by fans compulsivelyHumidity RangeLess than 30ºC: ≤95% Relative Humidity (RH)30ºC to 40ºC: ≤75% Relative Humidity (RH)40ºCto 50ºC: ≤45% Relative Humidity (RH)AltitudeOperating: Less than 3000 metersNon-Operating: Less than 15,000 metersMechanicalDimensions(W×H×D)261.5mm×112mm×318.4mmWeightwithout package: 3.2kgwith package: 4.5kgInterfacesUSB Host, USB Device, LANIP ProtectionIP2XCalibrationIntervalRecommend calibration interval is one yearTech SpecsGenerators / Counters/Function Generator TemplateChannels2Frequency Maximum25 MHzFrequency Minimum1 uHz (0.000001 Hz)FunctionsBurst, Noise, Pulse, Ramp, Sine, Square, Sweep, TriangleMax Amplitude Vpp @ 50 ohms10 VArbitraryYesSample Rate250 MSa/SScreen TypeLCDColor ScreenYesTriggeringYesCounter that displays frequency on screen.YesModulation TypesAM, FM, FSK, PSK, PWMGraphical DisplayYesMemory2 MB (2048 kB) Pengukur Elektronik Lainnya

Power Supply with 2 0-30V/3A channels, 1 5V/3A channel, and 10 mV/10 mA measurement resolution3 Outputs; total power up to 195WLow Ripple Noise <350 uVrms/2mVppFast transient response time: <50 usChannel isolation: CH1 || CH2,CH3OVP/OCP/OTP protection functionsBuilt in V, A, W measurements and waveform displaySupport for output Delay, Analysis, Monitor, and Preset functions3.5 inch FTF DisplayConnectivity including USB Host & Device, LAN, and Digital IOLatest Build. NO HEATSINK ISSUESDescriptionTriple Output, 195 Watt Power Supply Build Remote Communication You can build the remote communication between DP800 and PC over USB, LAN, RS232 or GPIB (option, can be extended via the USB-GPIB interface converter) interface.Remote Controls MethodsUser-defined ProgrammingYou can program and control the instrument using the SCPI (Standard Commands for Programmable Instruments)Send SCPI Commands via the PC SoftwareYou can control the power supply remotely by sending SCPI commands via the PC software (Ultra Sigma) provided by RIGOL. SCPI Command OverviewSCPI (Standard Commands for Programmable Instruments) is a standardized instrument programming language that is built upon the standard IEEE488.1 and IEEE 488.2 and conforms to various standards (such as the floating point operation rules in IEEE754 standard, ISO646 7-bit coded character for information interchange (equivalent to ASCII programming)). This section introduces the syntax, symbols, parameters and abbreviation rules of the SCPI commands.SCPI Status RegistersAll the SCPI instruments execute the status register operations in the same way. The status system records the various instrument states into three register sets: status byte register, standard event register, and questionable status register sets. The status byte register records the advanced summary informationreported by other register sets. The SCPI status systems of the DP800 series multi-channel models. OVERVIEW The Rigol DP832 is a very high-quality programmable laboratory power supply with three switchable outputs (+30 V/3 A, +30 V/3 A and +5 V/3 A) and a maximum power output of 195 W.Like all Rigol devices, the power supply features a very well constructed and easy to use interface offering comprehensive ease-of-use functions, such as programmable voltage curves. The menu has an intuitive structure.The Rigol DP832 features a relatively large (8.9 cm / 3.5") and easy to read TFT monochrome display. In addition to the normal digital displays for voltage, current, and power, these values can also be displayed as signal curves. A timer control can be used to set the output signal to different values in up to 2048 steps.The DP800 Series Power Supplies combine the ability to source, analyze, and coordinate over time in a powerful new package. The DP800 Series is a family of linear power supplies systems with 3 outputs and up to 195 Watts in total. With one channel isolated, users can reconfigure instruments into any number of systems or applications.Built in V, A, and W measurements make power monitoring easy, but additional wave tracking, timing, and analysis features mean there are even more ways to use the supplies. New digital triggering between instruments also makes it possible to reliably combine and connect supplies together. Intuitive to use for everything from education labs to the R & D bench, the DP800 family of power supplies provide incredible value for any application.Typical ApplicationsR&D Lab general purpose testingQuality Assessment inspectionBias power for RF/MW circuitsAutomotive electronic testProduction testingDevice or circuit characterization and troubleshootingIntuitive User Interface DP832 GUIAll important data such as voltage, current, power, and limit values can easily be displayed on the display with a diagonal size of 8.9 cm (3.5") and a resolution of 320x240 pixels.LAN SetupControl of the device can be integrated into your own applications, or by using LabView via these interfaces.Output DelayTiming OutputProgrammable TimerThe voltage and current settings can be changed automatically with a timer control. Up to 100 settings can be stored for this purpose, and then activated one after another for variable intervals (specified in seconds).V/A/W DisplayChanges in the measurement values and settings can be presented very well and in real-time using the integrated signal curve display. This makes it possible to detect things like current draw peaks, for example when the current limit is adjusted.Output Analysis FunctionThe analyzer can analyze the file recorded and provides the analysis results, including the number of groups, median, mode as well as the average, VAR, range, minimum, maximum and mean deviation of the voltage, current or power of different channel.Monitor SetupThe monitor can monitor the current output state of the instrument. When the user-defined monitor condition is met, the instrument executes the corresponding operation according to the setting in "Stop Mode", like showing a warning, shut off the output or produce a beep sound.Trigger In/OutThe rear panel of DP800A provides a digital I/O interface (as shown below) which supports trigger input and trigger output. The 4 data lines are mutually independent and can be used as trigger input line or trigger output line separately.In The BoxPower cordUSB data cableOne shorted deviceOne fuseQuick GuideNIST calibration certificate for the DP832ManualsRigol DP800 Series Power Supply Programming GuideRigol DP800 Series Power Supply Users ManualRigol DP800A Power Supply Users GuideRigol Ultra Sigma Software Users GuideProduct Selection GuideFull Line CatalogRigol DP800 Performance Verification GuideRigol Power Supply Declassification GuideSpec SheetsRigol DP800 Series Power Supply Data SheetRigol DP800A Specs Manufacturer SpecsRIGOL DP800 SERIES SPECIFICATIONSModelDP832ADP832DP831ADP811ADP821AChannels312DC Output (0°C to 40°C )     Voltage/currentCH1: 0 to 30V/0 to 3ACH2: 0 to 30V/0 to 3ACH3: 0 to 5V/0 to 3ACH1: 0 to 8V/0 to 5ACH2: 0 to +30V/0 to 2ACH3: 0 to -30V/0 to 2A0 to 20 V/ 0 to 10 A (Low Range) or 0 to 40 V/0 to 5 A (High Range)CH1: 0 to 8 V0 to 10 ACH2: 0 to 60 V0 to 1 A OVP/OCPCH1: 1mV to 33V/1mA to 3.3ACH2: 1mV to 33V/1mA to 3.3ACH3: 1mV to 5.5V/1mA to 3.3ACH1: 10mV~33V/1mA~3.3ACH2: 10mV~33V/1mA~3.3ACH3: 10mV~5.5V/1mA~3.3ACH1:1mV ~ 8.8V/0.1mA ~ 5.5ACH2:1mV ~ 33V/0.1mA ~ 2.2ACH3:-1mV ~ -33V/0.1mA ~ 2.2A0.1 V to 22 V or0.1 V to 44 VCH1: 0.1 to 8.8 V0.1A to 10.5A CH2: 0.1 to 66 V0.1A to 1.1A Load Regulation Rate ±(Output Percentage + Offset)  Voltage<0.01%+2mVCurrent<0.01%+250uALinear Regulation Rate ±(Output Percentage + Offset)  Voltage<0.01%+2mVCurrent<0.01%+250uARipples and Noise (20Hz to 20MHz)  Normal Mode Voltage<350μVrms/2mVppNormal Mode Current<2mArmsCommon Mode Current<1.5μArmsNot specifiedAnnual Accuracy [1] (25°C ±5°C ) ±(Output Percentage + Offset)  ProgrammingVoltage0.05% + 10mV0.15%+ 5mA0.05% + 10mVCH1: 0.05% + 10mVCH2: 0.1% + 25mVCurrent0.2% + 10mA0.2%+10mA0.1% + 10mA0.2% + 10mAReadbackVoltage0.05% + 5mV0.1%+20mV0.05% + 10mVCH1: 0.05% + 5mVCH2: 0.1% + 25mVCurrent0.15%+ 5mA0.2%+10mA0.1% + 10mA0.15% + 10mAResolution  ProgrammingVoltage1mV10mVWith high-resolution option:1mV1mV1mVCH1: 1 mVCH2: 10 mV Current1mA1mACH1: 0.3mACH2/CH3: 0.1mA0.5mACH1: 1 mACH2: 0.1 mAReadbackVoltage0.1mV10mVWith high-resolution option:0.1mV0.1mV0.1mVCH1: 1 mVCH2: 1 mV Current0.1mA1mAWith high-resolution option:0.1mA0.1mA0.1mACH1: 1 mACH2: 0.1 mADisplayVoltage1mV10mVWith high-resolution option:1mV1mV1mVCH1: 1 mVCH2: 10 mV Current1mA10mAWith high-resolution option:1mA1mA1mACH1: 1 mACH2: 0.1 mATransient Response Time  Less than 50μs for output to recover to within 15mV following a change in output current from full load to half load or vice versa.Command Processing Time [2]  <100msTemperature Coefficient per? (Output Percentage + Offset)     VoltageCH1/CH2: 0.01%+5mVCH3: 0.01%+2mV0.01%+2mV0.01%+3mVCurrent0.01%+2mA0.02%+3mA0.02%+3mAStability [3] ±(Output Percentage + Offset)  VoltageCH1/CH2: 0.02%+2mVCH3: 0.01%+1mVCH1: 0.03%+1mVCH2/CH3: 0.02% + 2mV0.02%+1mVCurrent0.05%+2mACH1: 0.1%+3mACH2/CH3: 0.05% + 1mA0.1%+1mATech SpecsPower Supplies/DC Power Supplies TemplateOutputsTripleVoltage Output 1VariableMax Voltage Output 130 VMin Voltage Output 10 VProgrammableYesCurrent Output 1VariableMax Current Output 13 AMin Current Output 10 AVoltage Output 2VariableMax Voltage Output 230 VMin Voltage Output 20 VCurrent Output 2VariableMax Current Output 23 AMin Current Output 20 AVoltage Output 3VariableMax Voltage Output 35 VMin Voltage Output 30 VCurrent Output 3VariableMin Current Output 30 AMax Current Output 33 AMeter TypeDigitalLinear/SwitchingLinearMax Display Resolution Current10 mAMax Display Resolution Voltage10 mVConstant current/voltageYesRemote SensingNoTest Equipment General AttributesUnique FeaturesLow Ripple Noise: <350 uVrms/2mVppFast Transient Response Time: <50us Channel isolation: CH1 || CH2,CH3Standard OVP/OCP/OTP protection functionsStandard Timing function Built in V,A,W measurements and waveform displaySupport Output Delay, Analysis, Monitor, Preset functionsIndependent control for each channel3.5 Inch TFT DisplayWarranty3 YEARSInterfaces I/OUSB Host, USB Product Weight9 KILOS (19.84 LBS)Product Height157 MM (6.18 IN)Product Length239 MM (9.41 IN)Product Width418 MM (16.46 IN)HTS/Schedule B Number8504409510ECCN Number3A992.aCalibration IncludedFactory CalibrationPower Supply Voltage120V/220V UniversalCountry of OriginChinaShipping Height11.7 INShipping Length14.5 INShipping Width22 INAlat Laboratorium Umum

Rigol DS1054Z Digital Oscilloscope 50 Mhz DSO 4 Channels50 MHz Digital Oscilloscope with 4 channels plus 12 Mpts memory, 1 GS/s sampling rateThe Number 1 Selling Oscilloscope 4 Years Running!4 Channels, 50 MHz BandwidthNow includes FREE software bundle BND-MSO/DS1000Z built into the unitUltraVision: Deeper memory 12 Mpts upgradable to 24 Mpts via a software key( this is not a typo.  This scope has 12 Megs of Memory standard! )Up to 30,000 wfms/s Waveform capture rateHUGE 7'' screen  WVGA(800X480) TFTUSB HOST, USB DEVICE, LAN, Aux (TrigOut /PassFail)Incredible display with multi-Level intensity grading displayRealtime  waveform  Record,Replay, function (Opt.)DescriptionRigol DS1054Z   Best Selling OscilloscopeFind out why the DS1054Z is one of the top selling oscilloscopes in the WORLD since its release in September 2014. Read the reviews! Let our customers tell you what they think of this unit. Schools, companies, students and home hobbyists love the DS1054Z. Backed by a 30 day money back guarantee you cannot go wrong with this unit.DS1054Z Features50 MHz Analog BandwidthTotal of 4 Analog ChannelsMaximum Waveform Capture Rate of up to 30,000 wfms/sIncludes 4 RP2200 150 MHz Passive HighZ ProbesLow noise floorUSB Host for Thumb DriveLarge 7" Display12 Mpts of Memory - upgradeable to 24  Customer Feedback"I have used the scope for basic measurements so far, mostly audio signals and comparisons of such signals. It works well and the construction is as good as that of expensive top-brand items. The packaging was adequate and protects the instrument well. RIGOL has tried hard to pass themselves as a decent company to buy equipment from and they have succeeded, at least with this scope. I have used lots of lab equipment for many years in college labs and this would fit perfectly in every lab, given its low price, specifications and support. Highly recommended for tight budgets and high expectations"Customer Submitted ImageUltraVisionRigol's innovative UltraVision technology provides a deeper memory depth of 12Mpts standard and is upgradeable to 24 Mpts (with purchase of MEM-DS1000Z). The DS1054z also provides the ability to quickly focus in on certain piece of a recorded waveform.Full VisibilityThe large 7" display of the DS1054z, with a resolution of 800 X 480 pixels makes it possible to view all channels on a single screen. This makes for better usability and more efficient analysis.Ultra-fast Sampling RateRigol has given the DS1000z series the ability to capture up to 30,000 waveform per second. This coupled with the 12 Mpts of memory and sampling rate of 1 GS/s makes this a great oscilloscope for nearly any application.Optional Waveform RecordingRigol has made recording waveforms an accessible option for all users with the simple purchase of the DS1000Z-REC software option. This allows users to go back and analyze previous data.Multi-Level Intensity Graded DisplayThis feature provides users the ability to focus in and visually detect event frequency over time.Advanced Triggering OptionsAdding to the flexibility of the DS1000Z line up, Rigol has added the option to purchase and advance triggering feature. This includes triggering options such RS232/URAT, I2C, SPI, Runt, Windows, Nth Edge, Delay, Time Out. This option can be purchased under product number AT-DS1000Z.Serial Bus Analysis OptionsBy purchasing the SA-DS1000Z Serial Bus Analysis Option, users can examine, decode and view RS232/URAT, I2C, SPI.Advanced Signal CalculationsRigol has integrated an advanced system of formulas designed to resolve complex signal calculations.In The BoxPower CordUSB Data CableQty. 4 of PVP2150 150 MHz Passive Probe with 1x:10x selector. Wide bandwidth of 35 MHz in 1x modeQuick GuideNIST calibration certificate for the DS1054ZAT-DS1000Z - Advanced Triggering OptionMEM-DS1000Z - Extends Deep Memory, up to 24MptsREC-DS1000Z - Real Time Waveform Record and Replay OptionSA-DS1000Z - Serial Bus Analysis Option. Includes RS-232/UART, I2C and SP SpecificationImageModelDS1054ZDS1074Z PlusDS1074Z-S PlusDS1104Z PlusDS1104Z-S PlusAnalog Bandwidth50 MHz70 MHz100MHzDigital Connector Port for optional MSO KitNoYesYesChannels4Max. Sample rate1GSa/s (Single-channel),  500MSa/s(Dual-channel), 250MSa/s(Fulll-channel)Max. Memory Depth12Mpts(std.), 24Mpts(option)Max. Waveform Capture rateUp to 30,000 wfms/sReal Time waveform Record,Replay and Analysis functionUp to 60, 000 Frames(Opt.)Std. ProbesRP2200 150MHz BW Passive Probe:4 setsBuilt in 2 Ch SourceNoNoYesNoYes SampleSample ModeReal-time SampleReal-time Sample Rate1 GSa/s (single-channel)500 MSa/s (dual-channel)250 MSa/s (four-channel)Peak Detect4 nsAveragingAfter both the channels finish N samples at the same time, N can be 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024.High ResolutionThe highest resolution is 12 bitMemory DepthSingle-channel: Auto, 12k pts, 120k pts, 1.2M pts, 12M pts and 24M pts (option) are availableDual-channel: Auto, 6k pts, 60k pts, 600k pts, 6M pts and 12M pts (option) are availableFour-channel: Auto, 3k pts, 30k pts, 300k pts, 3M pts and 6M pts (option) are availableInputNumber of Channelsfour-channelInput CouplingDC, AC or GNDInput Impedance(1 MΩ±2%) || (13 pF±3 pF)ProbeAttenuationCoefficient0.01X-1000X, 1-2-5 stepMaximum Input Voltage (1MΩ) Maximum input voltage of the analog channelCAT I 300 Vrms, CAT II 100 Vrms, transient overvoltage 1000 VpkWith RP2200 10:1 probe: CAT II 300 VrmsHorizontalTime Base Scale5 ns/div to 50 s/divTime Base Accuracy [1]≤ ± 25 ppmTime Base Drift≤ ± 5 ppm/YearDelay RangePre-trigger (negative delay): ≥1 screen widthPost-trigger (positive delay): 1 s to 100,000 sTime Base ModeY-T, X-Y, Roll, DelayedNumber of X-Ys1 pathWaveform Capture Rate [2]30,000 wfms/s (dots display)VerticalBandwidth (-3dB)DS1104Z: DC to 100 MHzDS1074Z: DC to 70 MHzSingle BandwidthDS1104Z: DC to 100 MHzDS1074Z: DC to 70 MHzVertical Resolution8 bitVertical Scale1 mV/div to 10 V/divOffset Range1 mV/div to 499 mV/div: ± 2 V500 mV/div to 10 V/div: ± 100 VBandwidth Limit120 MHzLow Frequency Response(AC coupling, -3dB)≤5 Hz (on BNC)Rise Time [1]DS1104Z: 3.5 nsDS1074Z: 5 nsDC Gain Accuracy [3]<10 mV: ±4% full scale≥10 mV: ±3% full scaleDC Offset Accuracy±0.1 div ± 2 mV ± 1% offsetChannel to ChannelIsolationDC to maximum bandwidth: >40 dBTriggerTrigger Level Range±5 div from the center of the screenTrigger ModeAuto, Normal, SingleHoldoff Range16 ns to 10 sHigh FrequencyRejection275 kHzLow FrequencyRejection275 kHzTrigger Sensitivity [1]1.0div (below 5mV or noise rejection is enabled)0.3div (above 5mV and noise rejection is disabled)Edge TriggerEdge TypeRising, Falling, Rising&FallingPulse TriggerPulse ConditionPositive Pulse Width (greater than, lower than, within specified interval)Negative Pulse Width (greater than, lower than, within specified interval)Pulse Width Range8 ns to 10 sRunt TriggerPulse ConditionNone, > (greater than), < (lower than), <> (within the specified interval)PolarityPositive, NegativePulse Width Range8 ns to 4 sWindows Trigger Windows TypeRising, Falling, Rising&FallingTrigger PositionEnter, Exit, TimeWindows Time8 ns to 10 sNth Edge TriggerEdge TypeRising, FallingIdle Time16 ns to 10 sNumber of Edges1 to 65535Slope TriggerSlope ConditionPositive Slope (greater than, lower than, within specified interval)Negative Slope (greater than, lower than, within specified interval)Time Setting8 ns to 10 sVideo TriggerSignal StandardSupport standard NTSC, PAL and SECAM broadcasting standardsSupport 480P, 576P HDTV standardsPattern TriggerPattern SettingH, L, X, Rising Edge, Falling EdgeDelay TriggerEdge TypeRising, FallingDelay Type> (greater than), < (lower than), <> (within the specified interval), >< (outside the specified interval)Delay Time8 ns to 10 sTimeOut Trigger Edge TypeRising, Falling, Rising&FallingTimeOut Value16 ns to 10 sDuration Trigger Pattern SettingH, L, XTrigger Condition> (greater than), < (lower than), <> (within the specified interval)Duration Time8 ns to 10 sSetup/Hold Trigger Edge TypeRising, FallingData PatternH, L,XSetup Time8 ns to 1 sHold Time8 ns to 1 sRS232/UART TriggerPolarityNormal, InvertTrigger ConditionStart, Error, Check Error, DataBaud2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps, UserData Bits5 bits, 6 bits, 7 bits, 8 bitsI2C TriggerTrigger ConditionStart, Restart, Stop, Missing Ack, Address, Data, A&DAddress Bits7 bits, 8 bits, 10 bitsAddress Range0x0 to 0x7F, 0x0 to 0xFF, 0x0 to 0x3FFByte Length1 to 5SPI TriggerTrigger ConditionTimeOut, CSTimeout Value16 ns to 10 sData Bits4 bit to 32 bitData Line SettingH, L, XMeasureManual mode | Voltage deviation between cursors (ΔV)Time deviation between cursors (ΔT)Reciprocal of ΔT (Hz) (1/ΔT)Track mode | Voltage and time values of the waveform pointAuto mode | Allow to display cursors during auto measurementAuto MeasurementMeasurements of Maximum, Minimum,Peak-Peak Value, Top Value, Bottom Value,Amplitude, Average, Mean Square Root,Overshoot, Pre-shoot, Frequency, Period, RiseTime, Fall Time, Positive Pulse Width, NegativePulse Width, Positive Duty Cycle, NegativeDuty Cycle, Delay A~B , Delay A~B , PhaseA~B , Phase A~BNumber ofMeasurementsDisplay 5 measurements at the same timeMeasurementRangeScreen Region or Cursor RegionMeasurementStatisticCounterAverage, Max, Min, Standard DeviationNumber of MeasurementsHardware 6 bits counter (channels areselectable)MathWaveformA+B, A-B, A×B, A/B, FFT, &&, ||, ^, !, intg, diff, sqrt, lg, ln, exp, absFFT WindowRectangle, Hanning, Blackman, Hamming,Flat Top,TriangleFFT DisplaySplit, Full ScreenFFT Vertical ScaledB/dBm, VrmsNumber of Busesfor Decoding2Decoding TypeParallel (standard), RS232/UART (option), I2C (option), SPI (option)DisplayDisplay Type7.0 inches TFT LCD displayDisplay Resolution800 horizontal×RGB×480 vertical pixelDisplay Color160,000 Color (TBD)Persistence TimeMin, 50 ms, 100 ms, 200 ms, 500 ms, 1 s, 2 s, 5 s, 10 s, 20 s, InfiniteDisplay TypeDots, VectorsI/OStandard PortsUSB HOST, USB DEVICE, LAN, Aux (TrigOut /PassFail)Signal Sourse (DS1000Z-S) Number of Channels 2Sample Rate 200 MSa/sVertical Resolution 14 bitsHighest  Frequency 25 MHzStandard Waveform Sine, Square, Pulse, Triangle, Noise, DCArbitrary Waveform Since, Exp.Rise, EXP.Fall, ECG, Gauss, Lorentz, HaversineSine Frequency Range 0.1 Hz to 25 MHz Flatness ±0.5 dB (relative to 1 kHz) Harmonic Distortion -40 dBc Stray (Non-Harmonic) -40 dBc Total Harmonic Distortion 1% Signal-to-Noise ration 40 dBSquare/Pulse Frequency Range 0.1 Hz to 15 MHz Rise/Fall time <15 ns Overshoot <5% Duty Cycle 10% to 90% Duty Cycle  Resolution 1% to 10 ns (select the greater one) Minimum Pulse Width 20 ns Pulse Width Resolution 10 ns or 5 bits (select the greater one) Jitter 500 psTriangle Frequency Range 0.1 Hz to 100 kHz Linearity 1% Symmetry 0 to 100%Noise [1] Bandwidth25 MHzInternal Generatedwaveforms Frequency Range 0.1 Hz to 1 MHzArbitrary Waveforms Frequency Range 0.1 Hz to 10 MHz Waveform Length 2 to 16k ptsFrequency Accuracy100 ppm (lower than 10 kHz)50 ppm (greater than 10 kHz) Resolution 0.1 Hz or 4 bit, select the greater oneAmplitude Output Range 20 mVpp to 5 Vpp, High-resistance10 mVpp to 2.5 Vpp, 50 Ω Resolution 100 μV or 3 bit, select the greater one Accuracy 2% (1 kHz)DC Offset Range ±2.5 V, High-resistance±1.25 V, 50 Ω Resolution 100 μV or 3 bit, select the greater one Accuracy 2% (1 kHz)General SpecificationsProbe Compensation OutputOutput Voltage [1]About 3 V, peak-peakFrequency [1]1 kHzPowerPower Voltage100-240 V, 45-440 HzPowerMaximum 50 WFuse2 A, T degree, 250 VEnvironmentTemperature RangeIn operation: 0°C to +50°COut of operation: -40°C to +70°CCooling MethodFanHumidity Range0° to +30°C : ≤95°C relative humidity+35°C to +40°C : ≤75°C relative humidity+40°C to +50°C : ≤45°C relative humidityAltitudeIn operation: under 3,000 metersOut of operation: under 15,000 metersMechanicalDimensions [4]Width×Height×Depth =313.1 mm× 160.8 mm×122.4 mmWeight [4]Without package | 3.2 kg ± 0.2 kgWith package | 3.8 kg ± 0.5 kgAdjustment Interval The recommended calibration interval is one year.Regulation StandardsElectromagnetic2004/108/ECCompatibilityExecution standard EN 61326-1:2006 EN61326-2-1:2006SafetyUL 61010-1:2004; CAN/CSA-C22.2 NO.61010-1-2004;EN 61010-1:2001; IEC 61010-1:2001Tech SpecsOscilloscopes/Digital Oscilloscopes TemplateBandwidth50 MhzChannels4Sampling Rate1 GS/S Memory12 MP [megapoints] (12288 kB)Rise Time7 nsScreen Size7 INBits8Battery OptionsNoTest Equipment General AttributesUnique FeaturesThe Number 1 Selling Oscilloscope of 20154 Channels, 50 MHz BandwidthUltraVision: Deeper memory 12 Mpts upgradable to 24 Mpts via a software key( this is not a typo. This scope has 12 Megs of Memory standard! )Up to 30,000 wfms/s Waveform capture rateHUGE 7'' screen WVGA(800X480) TFTUSB HOST, USB DEVICE, LAN, Aux (TrigOut /PassFail)Incredible display with multi-Level intensity grading displayRealtime waveform Record,Replay, function (Opt.)A variety of Math FunctionsFFT function standardA variety of Trigger FunctionsOptional Serial Bus Triggering and Decoding functions(RS232,I2C,SPI) These are software keysStandard Mask test functionAutomatic Measurements with StatisticsThis scope is truly amazing for the price. Deep memory, beautiful screen, 4 channels, free software, USB host interface, standard usb interface on the back, LAN/Ethernet standard, Aux (TrigOut /PassFail)Warranty3 YEARSSafety ApprovalCE, CSAInterfaces I/OLAN / Ethernet, LXI, USB Host, USBProduct Weight3 KILOS (6.61 LBS)Product Height12.00 INProduct Length18.00 INProduct Width11.00 INShipping Weight4.2 KILOS (9.26 LBS)Data LoggingYes HTS/Schedule B Number9030201000ECCN Number3A992.aCalibration IncludedFactory CalibrationPower Supply Voltage120V/220V UniversalCountry of OriginChinaShipping Height12.00 INShipping Length18.00 INShipping Width11.00 INAlat Laboratorium Umum

Rigol DM3068 6 1/2 Digit Benchtop Digital Multimeter6 1/2 Digit Benchtop Digital Multimeter with USB, LXI, GPIB, and RS-232 interfaces standardTrue 6 ½ digit resolutionMinimum Integration Time is 0.006 PLC for more than 8,000 measurements per secondTrue-RMS AC Voltage & Current measurements View real time measurement trending or histograms from the front panelBuilt-in comprehensive configurations for a variety of temperature sensorsGPIB, USB, RS-232, and LXI-C (Ethernet) ConnectivityDescriptionDM3068 is a digital multimeter designed with 6 ½ digits readings resolution especially fitting to the needs of high-precision, multifunction and automatic measurement. It adopts many today's new technologies to achieve high performance, abundant features in the same class. It's designed to aim at the requirements of the largest DMM market from the research, education,industrial electronics,consumer electronics and automotive industries with its innovative technology,industry leading specifications,powerful measurement functions and broad analysis capabilities.The Model DM3068 DMM gives reliable, cost effective, full DMM capabilities measuring DCV, ACV, DCI, ACI, Resistance (2 & 4 Wire), Capacitance, Diode Test, Frequency, and Temperature. These DMMs are designed for simple and efficient bench top use, but include software options for datalogging and remote programming from almost any interface. The DM3068 is a great bench tool for high performance, reliable measurements, but also a new high speed data acquisition option for many measurement challenges. Advanced FunctionsReal 6 ½ digits resolutionEasy to measure AC signal with double display Standard Capacitor measurement function10 groups Preset function Any sensor” function Support multiple temperature sensorsSupport multiple commandsFile management (support U-disk and local storage) Math functionStatistic function Histogram displayTrendline display In The BoxSpare FusesLEAD-DMMCalibration CertificatePower CordUSB CablePacking KitNIST calibration certificateManufacturer SpecsSpecificationDisplay256 × 64 LCD, dual display, graphical menu, selectable Chinese or English, online help.Power SupplyAC 100 V - 120 V, 45 Hz - 440 HzAC 200 V - 240 V, 45 Hz - 66 HzDetect the power-line frequency automatically at power-on, 400Hz defaults to 50HzPower Consumption25 VA MaxWorking EnvironmentFull accuracy for 0 °C to 50 °CFull accuracy to 40 °C, 80% R.H., Non-coagulationStorage Temperature- 40 °C to 70 °COperation AltitudeUp to 2000 mSafetyIEC 61010-1; EN 61010-1; UL 61010-1; CAN/CSA-C22.2 No. 61010-1Measurement CAT I 1000 V/CAT II 300 VPollution Degree 2EMCEN 61326-1WeightAbout 3.2 kg (without package)Dimension(height × width × length): 107.0mm × 231.6mm × 290.5mmRemote InterfaceGPIB, 10/100 Mbit LAN, USB 2.0 Full Speed Device & Host (support USB flash device), RS-232CProgramming LanguageSCPILXI CompatibilityLXI Class C, Version 1.2Warm-up Time90 minutes MeasurementFunctionRangeFrequencyRange/TestCurrentAccuracy: 1 Year± (%of reading+%of range)DC Voltage200 mV - 1000 V 0.0035+0.0005DC Current200 uA - 10 A 0.050+0.005AC Voltage (RMS)200 mV - 750 V 0.06+0.03AC Current (RMS)20 mA - 10 A 0.10+0.04Resistance(2-wire and 4-wire)200 Ω - 100 MΩ 0.010+0.001Capacitance2 nF - 10000 uF 1 + 0.5Diode2.0 V  Continuity2 kΩ  Frequency and Period200 mV - 750 V3 Hz - 1 MHz / 1usec – 0.33 sec0.007Tech SpecsMultimeters TemplateTypeDigitalStyleBenchMeasures AC VYesMeasures DC VYesMeasures AC AYesMeasures DC AYesTrue RMSYesMaximum Voltage AC750 VMinimum Voltage AC200 mVResolution AC Volts1 uV (0.001 mV)Maximum Voltage DC1000 VMinimum Voltage DC200 mVResolution DC Volts1 uV (0.001 mV)Maximum Current AC10 AMinimum Current AC20 mAResolution AC Current0.1 uA (0.00010 mA)Maximum Current DC10 AMinimum Current DC200 uA (0.2 mA)Resolution DC Current1 nA (0.000001 mA)Basic Accuracy V DC.005% Reading + .003% Range# Digit Display6.5+Counts2000000 .BacklightNoManual/AutorangingBothDual DisplayYesAnalog Bargraph on DisplayNoDecibelsYesResistanceYesFrequencyYesContinuityYesCapacitanceYesTemperatureYesDiode TestingYesCAT RatingIICAT Voltage1,000 V, 600 V Intrinsically SafeNoPeak HoldYesOverload ProtectorYesKelvin 4-Wire Measurement CapabilityYesWireless DisplayNoData HoldYesTest Equipment General AttributesWarranty3 YEARSSafety ApprovalCEInterfaces I/OGPIB, LAN / Ethernet, LXI, RS-232, USB Host, USBProduct Weight3.5 KILOS (7.72 LBS)Product Height107 MM (4.21 IN)Product Length290.5 MM (11.44 IN)Product Width231.6 MM (9.12 IN)Data LoggingYes HTS/Schedule B Number9030320000ECCN Number3A992.aCalibration IncludedFactory CalibrationPower Supply Voltage120V/220V UniversalCountry of OriginChinaShipping Height10.00 INShipping Length18.00 INShipping Width14.00 INAlat Laboratorium Umum

Rigol DM3058E 5 1/2 Digit Low cost Benchtop Digital Multimeter with USB and RS-232 only5 1/2 Digit Benchtop Digital Multimeter with USB and RS-232 interfaces standardReal 5 ½ digits readings resolutionUp to 123 rdgs/s of measurement speedTrue-RMS AC Voltage Current measuringQuickly Save or Recall the 10 groups of Preset ConfigurationPreset 10 groups of Standard Sensor Configuration, built-in Thermocouple compensate in Cold TerminalClone or backup all the configurations within instrument into other DM3058 via U-discThe first 5 ½ digit digital multimeter passing LXI Criterion in industry, which can achieve system integration easily (DM3058 ONLY)With easy, convenient and flexible random sensor measurement control software: UltraSensorStandard configuration interface: USB Device, USB Host, RS-232, and support U-disc storage and Web remote controlDescriptionDM3058E is a digital multimeter designed with 5 ½ digits readings resolution especially fitting to the needs of high-precision, multifunction, and automatic measurement.A high quality digital tabletop multimeter of the DM3050 series with a sampling rate of max. 120 Sa/s.These Rigol multimeters have a very sophisticated and easy to use interface and provides plenty functions for all measurement tasks. The use of the menu navigation is very intuitional and the device will provide precise results in its many application areas. With the help of a computer you can perform long running monitoring tasks too.The LC-Display is with its 256x64 pixels easy to read and provides a very good overview over all features. The display has a resolution of 5½ digits (max. count 240.000).Math FunctionMax, Min, Average, Standard Deviation, Pass/Fail, dBm, dB, Relative Measurement and Vertical chartDouble DisplayMirror Image Configuration Double Display function makes your measurements achieve maximum results with little effort. It can display two performances of a signal simultaneously instead of two multimeters or measurements in the past.All the configurations (system and sensor configuration) of DM3058 can be cloned into other DM3058 on product line via U-disc to improve work efficiency. Preset ModePass/Fail Based on Preset Mode, the worker operation on product line could be greatly simplified. Besides, 10 groups of Preset Configuration are available to be stored and recalled.Pass/Fail test function can prompt for signals beyond the range based on specified higher and lower limit, and make test result more obvious. Unique Random SensorLXI & Web Remote ControlDM3058 is the first 5½ digit digital multimeter passing LXI Criterion in industry that makes system integration easier.Remote Control for DM3058 can be achieved by virtual panel from Web page in the same operation way with front panel of instrument.Random Sensor measurement is a new conception being forward to meet user’s requirements. By this particular function, you can easily connect Pressure Sensor or Flux Sensor or Temperature Sensor.DM3058 supports DCV, DCI, and Freq, 2WR, 4WR and Thermocouple TC 6 kinds of Sensor in all. Meanwhile, there are 10 groups of basic Sensor preset within the instrument.Also, the built-in Thermocouple Cold Terminal temperature sensor can be used for measuring temperature of thermocouple UltraSensor Software InterfaceUltraSensor is used to control random sensor. The main functions include:Create a project for random sensor measurement which can be download to DM3058;Connect with DM3058 to achieve random sensor measurement;Monitor the sensor data in real time and show them in the form of figure;Enable to save data in the format of CSV and TXT, and reference curve in the format of BMP. Standard AccesoriesPower CordTest Lead KitBackup FuseUSB CableOptional Accesories CD-ROMQuick GuideWarranty CardIn The BoxPower Cord that fits the standard of destination countryTwo Test Leads (black and red)Two Alligator Clips (black and red)USB Data CableBackup FuseQuick GuidePacking KitNIST calibration certificate Manufacturer SpecsDC CharacteristicsAccuracy ± (% of reading + % of range)[1]FunctionRange[2]Test current or Load voltage1 Year 23°± 5°Temperature Coefficient 0° - 18° 28° - 50°DC Voltage200.000 mV200.000 mV200.000 mV200.000 V1000.00 V[4] 0.015 + 0.0040.015 + 0.0030.015 + 0.0040.015 + 0.0030.015 + 0.0030.0015 + 0.00050.0010 + 0.00050.0020 + 0.00050.0015 + 0.00050.0015 + 0.0005DC Current200.000 µA2.00000 mA20.00000 mA200.00000 mA2.00000 A10.0000 A[5]<8 mV<80 mV<0.05 V<0.5 V<0.1 V<0.3 V0.055 + 0.0050.055 + 0.0050.095 + 0.0200.070 + 0.0080.170 + 0.0200.250 + 0.0100.003 + 0.0010.002 + 0.0010.008 + 0.0010.005 + 0.0010.013 + 0.0010.008 + 0.001Resistance[3]200.000 Ω2.00000 kΩ20.0000 kΩ200.000 kΩ2.00000 MΩ10.0000 MΩ100.000 MΩ1 mA1 mA100 µA10 µA1 µA200 nA200 nA || 10 MΩ0.030 + 0.0050.020 + 0.0030.020 + 0.0030.020 + 0.0030.040 + 0.0040.250 + 0.0031.75 + 0.0040.0030 + 0.00060.0030 + 0.00050.0030 + 0.00050.0030 + 0.00050.0040 + 0.00050.0100 + 0.00050.2000 + 0.0005Diode Test2.0000 V[6]1 mA0.05 + 0.010.0050 + 0.0005Continuity Test2000 Ω1 mA0.05 + 0.010.0050 + 0.0005Remarks:[1] Specifications are for 0.5 hour warm-up, “Slow” measure and calibration temperature 18° - 28°.[2] 20% over range on all ranges except for DCV 1000 V, ACV 750 V, DCI 10 A and ACI 10 A.[3] Specifications are for 4-wire measure or 2-wire measure under “REF” operation. ± 0.2 Ω of extra errors will begenerated if perform 2-wire measure without “REF” operation.[4] Plus 0.02 mV of error per 1 V after the first ± 500 VDC.[5] 30 seconds OFF after 30 seconds ON is recommend for the continuous current that higher than DC 7 A or AC RMS7 A.[6] Accuracy specifications are only for voltage measuring at input terminal. The typical value of current undermeasure is 1 mA. Voltage drop at the diode junction may vary with current supply.DC VoltageInput Resistance200 mV and 2 V range 10 MΩ or >10 GΩ selectable(Input signals that exceed ± 2.5 V in these ranges will pass the 100 kO (typical) clampresistance.)Input Bias Current<90 pA, 25°Input Protection1000 V on all rangesCMRR (common mode rejection ratio)120 dB (For the 1 kΩ unbalanced resistance in LO lead, maximum ± 500 VDC)NMRR (normal mode rejection ratio)60 dB at “slow” measurement rate20 dB are added if open the “AC filter” (Settling time will add 0.35 s while sourceimpedance nears zero)ResistanceTesting Method4-wire resistance or 2-wire resistance optionalFor current source refer to LO inputOpen-circuit VoltageP/F in <8 VMaximum Lead Resistance (4-wire resistance)10% of ranges, on the range of 200 Ω, 1 kΩ, for each lead1 kΩ, on all other ranges, for each leadInput Protection1000 V, on all rangesDC CurrentShunt Resistor200 µA sampling voltage < 8 mV2 mA sampling voltage < 80 mV1Ω for 20 mA, 200 mA0.01 Ω for 2 A, 10 AInput ProtectionRear panel: accessible 10 A, 250 V fast-melt fuseInternal: 12 A, 250 V slow-melt fuseContinuity / Diode TestMeasurement Method1 mA ± 5% constant-current source, < 8 V open-circuit voltageResponse Time123 samples/sec, with beeperContinuity ThresholdAdjustable between 1 Ω and 2000 ΩInput Protection1000 VSetup time AttentionsThe setup time about voltage measurement is influenced by source resistance and media characteristics of cable aswell as input signaAC CharacteristicsAccuracy ± (% of reading + % of range)[1]FunctionRange[2]Frequency Range1 Year 23°± 5°Temperature Coefficient 0° - 18° 28° - 50°True RMS AC Voltage[3]200.000 mV20 Hz – 45 Hz45 Hz – 20 kHz20 kHz – 50 kHz50 kHz – 100 kHz1.5 + 0.100.2 + 0.051.0 + 0.053.0 + 0.050.01 + 0.0050.01 + 0.0050.01 + 0.0050.05 + 0.0102.00000 V20 Hz – 45 Hz45 Hz – 20 kHz20 kHz – 50 kHz50 kHz – 100 kHz1.5 + 0.100.2 + 0.051.0 + 0.053.0 + 0.050.01 + 0.0050.01 + 0.0050.01 + 0.0050.05 + 0.01020.0000 V20 Hz – 45 Hz45 Hz – 20 kHz20 kHz – 50 kHz50 kHz – 100 kHz1.5 + 0.100.2 + 0.051.0 + 0.053.0 + 0.050.01 + 0.0050.01 + 0.0050.01 + 0.0050.05 + 0.010200.000 V20 Hz – 45 Hz45 Hz – 20 kHz20 kHz – 50 kHz50 kHz – 100 kHz1.5 + 0.100.2 + 0.051.0 + 0.053.0 + 0.050.01 + 0.0050.01 + 0.0050.01 + 0.0050.05 + 0.010750.000 V20 Hz – 45 Hz45 Hz – 20 kHz20 kHz – 50 kHz50 kHz – 100 kHz1.5 + 0.100.2 + 0.051.0 + 0.053.0 + 0.050.01 + 0.0050.01 + 0.0050.01 + 0.0050.05 + 0.010True RMS AC Current[5]20.0000 mA20 Hz - 45 Hz45 Hz - 2 kHz2 kHz -10 kHz1.5 + 0.100.50 + 0.102.50 + 0.200.015 + 0.0150.015 + 0.0060.015 + 0.006200.000 mA20 Hz - 45 Hz45 Hz - 2 kHz2 kHz -10 kHz1.5 + 0.100.50 + 0.102.50 + 0.200.015 + 0.0150.015 + 0.0060.015 + 0.0062.00000 A20 Hz - 45 Hz45 Hz - 2 kHz2 kHz -10 kHz1.5 + 0.100.50 + 0.102.50 + 0.200.015 + 0.0150.015 + 0.0060.015 + 0.00610.0000 A[5]20 Hz - 45 Hz45 Hz - 2 kHz2 kHz -10 kHz1.5 + 0.100.50 + 0.102.50 + 0.200.015 + 0.0150.015 + 0.0060.015 + 0.006Additional wave crest factor error (not Sine)[6]Wave crest coefficientError (% range)1 - 22 - 30.050.2Remarks:[1] Specifications are for 0.5 hour warm-up, “Slow” measure and calibration temperature 18° - 28°.[2] 20% over range on all ranges except for DCV 1000 V, ACV 750 V, DCI 10 A and ACI 10 A.[3] Specifications are for amplitude of sine wave input >5% of range. 750 V range limited to 8x10 7 Volt-Hz. For inputsfrom 1% to 5% of range and <50 kHz, add 0.1% of range extra error. For 50 kHz to 100 kHz, add 0.13%[4] Specifications are for sine wave input >5% of range. 0.1% errors will be added when the range of input sine waveis 1% ~ 5%.[5] 30 seconds OFF after 30 seconds ON is recommend for the continuous current that higher than DC 7 A or AC RMS7 A.[6] For frequency<100 Hz.True RMS AC VoltageMeasurement MethodAC coupled true RMS measure - up to 1000 V DC bias are permitted on every rangeWave Crest Factor≤ 3 at full scaleInput Impedance1 MΩ± 2% in parallel with <100 pF on all rangesAC Filter Bandwidth20 Hz ~ 100 kHzCMRR (common mode rejection ratio)60 dB (For the 1 kΩ imbalance resistance among Lo lead and <60 Hz, maximum ± 500 VDC)True RMS AC CurrentMeasurement MethodDC coupled to the fuse and shunt; AC coupled the True RMS measurement (measures the AC components only)Wave Crest Factor≤ 3 at full scaleMaximum InputThe DC + AC current peak value <300% of range. The RMS current including DC current is <10 AShunt Resistor1 Ω for 20 mA, 200 mA0.01 Ω for 2 A, 10 AInput ProtectionRear panel: accessible 10 A, 250 V fast-melt fuseInternal: 12 A, 250 V slow-melt fuseSetup Time AttentionsMake sure that the RC return at input terminal has been in a stable state completely (higher than 1 s) before accuratemeasurement;Input >300 Vrms (or >5 Arms) will cause the self heating of the signal conditioning component to generate error, thiserror is included in the characteristics of the instrument. Internal temperature variation results from the self heatingwill cause additional an error on ac range that is lower than 0.03% of readings, and it will disappear after a fewminutesFrequency and Period CharacteristicsAccuracy ± (% of reading + % of range)[1]FunctionRange[2]Frequency Range1 Year 23°± 5°Temperature Coefficient 0° - 18° 28° - 50°Remarks:[1] Specifications are for 0.5 hour warm-up.[2] Except for special marks, the AC input voltage is 15% to 120% of range when <100 kHz and 40% to 120% ofrange when >100 kHz. 750 V range is limited to 750 VRMS. 200 mV ranges is for full scale or higher. For inputsfrom 30 mV to 200 mV, multiply total % of reading error by 10.[3] For AC input current from 15% to 120% of range except where noted. 20 mA range specifications are for full scale.For inputs from 5 mA to 20 mA, multiply total % of reading error by 10. 10 A range is for AC input current from25% to 100% of range.Frequency and PeriodMeasurement Method: Reciprocal-counting technique, AC-coupled input, AC voltage or AC current measurement functionMeasure AttentionsGenerally, errors are leaded into all frequency counters when measuring low voltage or low frequency signal.Shielding input can extremely help to reduce measuring errors caused by exterior noiseSetup Time AttentionsIf the variational DC components appeared in signals under measure, errors may be caused while measuring periodor frequency. Please ensure that the RC loop at input terminal must be stable during exact measuring (higher than 1sec)Capacitance CharacteristicsAccuracy ± (% of reading + % of range)[1,2]FunctionRange[2]Maximum Testing Current1 Year 23°± 5°Temperature Coefficient 0° - 18° 28° - 50°Capacitance2.000 nF20.00 nF200.0 nF2.000 µF200 µF10000 µF200 nA200 nA2 µA10 µA100 µA1 mA3 + 1.01 + 0.51 + 0.51 + 0.51 + 0.52 + 0.50.08 + 0.0020.02 + 0.0010.02 + 0.0010.02 + 0.0010.02 + 0.0010.02 + 0.001Remarks:[1] Specifications are for 0.5 hour warm-up and “REF” operation. Using of non-film capacitor may generate additionalerrors.[2] Specifications are for from 1% to 120% on 1 nF range and ranges from 10% to 120% on other ranges.Capacitance MeasuringMeasurement MethodMeasure the rate of change of voltage generated during the current flowing the capacitanceConnection Type2-wireInput Protection1000 V on all rangesMeasure Attentions:Small capacitance is easily influenced by external noise and thus causes errors while measuring, shielding input canextremely help to reduce this kind of errorsOther Measuring CharacteristicsTriggering and MemorySamples/Trigger1 ~ 2000Trigger Delay8 ms ~ 2000 ms optionaExternal Trigger InputInput LevelTrigger ConditionInput ImpendenceMin PulseTTL compatible (High level when left input terminal is hanging in the air)Selectable>20 kΩ,500 µsVMC OutputElectric LevelOutput PolarityInput ImpedanceTTL compatible ( input >=1 kohm loads)straight polarity and negative polarity optional200 ohm, typicalArbitrary SensorSupport for multiply types of sensor such as Thermocouple, DC Voltage, DC Current, Resistance (2-wire or 4-wire)and Frequency output; With thermocouple compensation at cold junction.Output Polarity: straight polarity and negative polarity optionalPreset ITS-90 transform of B, E, J, K, N, R, S and T thermocouple and transform of platinum Pt100, Pt385 resistancetemperature sensorMath FunctionsPass/Fail, REL (RELative), Min/Max/Average, dBm, dB, Hold, Historgram, Standard deviationHistory RecordsVolatile Memory2000 readings of history recordsNonvolatile Memory10 gourps of history records (2000 readings/group); 10 groups of sensor records: (1000readings/group); 10 groups of setting records of instrument; 10 groups of setting recordsof arbitrary sensor; support U-disk external storageGeneral SpecificationsPower SupplyAC 100 V ~ 120 V45 Hz ~ 440 HzAC 200 V ~ 240 V45 Hz ~ 66 HzConsumption20 VA peak valueMechanismDimension107.0 mm× 231.6 mm× 290.5 mmWeight2.5 kgOther CharacteristicsDisplay ScreenLCD display with 256× 64 lattices, support for Double display, Menu display, Operatinghelp and English/Chinese bilingual.Operating EnvironmentFull accuracy from 0° to 50°; 80% R.H. and 40°, non condensingStorage Temperature: -20° ~ 70°Shock and Vibration: conforming to MIL-T-28800E, III, 5 level (only for sine)height above sea level: up to 3000 metersSafetyConforming to IEC61010-1: 2001. Measure CAT I 1000 V/CAT II 600 VClass of pollution: 2Remote InterfaceGPIB, 10/100Mbit LAN, USB2.0 Full Speed Device & Host(U disc available), RS-232CProgrammer LanguageRIGOL 3058 SCPI, FLUKE45, Agilent34401ALXI CompatibilityLXI Class C, Version1.1Warm Up Time30 minutesTech SpecsMultimeters TemplateTypeDigitalStyleBenchMeasures AC VYesMeasures DC VYesMeasures AC AYesMeasures DC AYesTrue RMSYesMaximum Voltage AC750 VMinimum Voltage AC200 mVResolution AC Volts1 uV (0.001 mV)Maximum Voltage DC1000 VMinimum Voltage DC200 mVResolution DC Volts1 uV (0.001 mV)Maximum Current AC10 AMinimum Current AC20 mAResolution AC Current0.1 uA (0.00010 mA)Maximum Current DC10 AMinimum Current DC200 uA (0.2 mA)Resolution DC Current1 nA (0.000001 mA)Basic Accuracy V DC.005% Reading + .003% Range# Digit Display5.5Counts240000 .BacklightYesManual/AutorangingBothDual DisplayYesAnalog Bargraph on DisplayNoDecibelsYesResistanceYesFrequencyYesContinuityYesCapacitanceYesTemperatureNoDiode TestingYesCAT RatingIICAT Voltage1,000 V, 600 V Intrinsically SafeNoPeak HoldYesOverload ProtectorYesKelvin 4-Wire Measurement CapabilityYesWireless DisplayNoData HoldYesTest Equipment General AttributesWarranty3 YEARSSafety ApprovalCEInterfaces I/ORS-232, USB Host, USBProduct Weight2.5 KILOS (5.51 LBS)Product Height107 MM (4.21 IN)Product Length290.5 MM (11.44 IN)Product Width231.6 MM (9.12 IN)Data LoggingYes HTS/Schedule B Number9030320000ECCN Number3A992.aCalibration IncludedFactory CalibrationPower Supply Voltage120V/220V UniversalCountry of OriginChinaShipping Height10.00 INShipping Length18.00 INShipping Width14.00 IN Alat Laboratorium Umum

Rigol DSA832E-TG Spectrum Analyzer (9kHz to 3.2GHz) with Tracking Generator3.2 GHz Spectrum Analyzer with Built-In Tracking GeneratorAs of 4/1/2017 - Includes Preamplifier Option PA-DSA832 Standard (Previously a $599 add on)DSA832E-TG Spectrum Analyzer, 9 kHz to 3.2 GHz with Tracking GeneratorAll-Digital IF TechnologyFrequency Range from 9 kHz to 3.2 GHzMin. -148 dBm Displayed Average Noise Level (Typ.)Min. <-90 dBc/Hz @ 10 kHz Offset Phase NoiseLevel Measurement Uncertainty <1.0 dB10 Hz Minimum Resolution BandwidthUp to 3.2 GHz Tracking Generator (DSA832E-TG)Advanced Measurement Functions (Opt.)EMI Filter & Quasi-Peak Detector Kit (Opt.)VSWR Measurement Kit (Opt.)PC Software (Opt.)Description3.2GHz Spectrum Analyzer with Tracking Generator  IF Design BenefitsThe ability to measure smaller signals: on the basis of this technology, the IF filter enables smaller bandwidth settings, which greatly reduce the displayed average noise level.The ability to distinguish between small signals by frequency: using the IF filter with the smallest bandwidth setting, it is possible to make out signals with a frequency difference of only 10 Hz. High precision amplitude readings: this technology almost eliminates the errors generated by filter switching, reference level uncertainty, scale distortion, as well as errors produced in the process of switching between logarithmic and linear display of amplitude when using a traditional analog IF design.Higher reliability: compared with traditional analog designs, the digital IF greatly reduces the complexity of the hardware, the system instability caused by channel aging, and the temperature sensitivity that can contribute to parts failure.High measurement speed: the use of digital IF technology improves the bandwidth precision and selectivity of the filter, minimizing the scanning time and improving the speed of the measurement.DSA800E Series Spectrum Analyzer DSA800E series spectrum analyzers which are small, light and cost-effective, are portable spectrum analyzers designed for starters. Configured with easy-to-operate numeric keyboard, high-resolution color LCD display and various remote communication interfaces, they can be widely used in various fields, such as education, company research and development as well as industrial manufacture. For design and development implementing Wi-Fi, Bluetooth, and other RF standards, the SSB Phase Noise down as low as -98 dBc/Hz at a 10 KHz offset empowers engineers to more accurately analyze modulations and noise surrounding their signals of interest. This becomes important for debugging and immunity testing of transceiver systems. The 7.5 GHz instrument enables engineers to investigate the 3rd harmonic of all of their critical 2.4 GHz applications while the 3.2 GHz models enable primary investigation of those signals as well as EMC measurements past the 3 GHz threshold. Additionally, resolution bandwidth settings down to 10 Hz means more precise visualization of low power RF signals. Whether you are still debugging your RF transceiver set, designing layout and configuration changes to maximize efficiency, or testing your system in noisy environments the DSA800 series spectrum analyzers will help you to quickly and easily identify and analyze your areas of concern. Rigol DSA800E Spectrum Analyzer Attractive Profile Rigol DSA800E Spectrum Analyzer Rear Panel Features and Benefits  Distinguish the two nearby signals clearly with the 10Hz RBW  Quickly compare the spectrums with different color trace  Readout the spectrum peak values with the peak table function  Measure lower level signal with the preamplifier turn on  Phase noise < -90 dBc/Hz @10 kHz offset  EMI kit (EMI filter & Quasi-peak & Pass/Fail  AM Signal Demodulation VSWR measurementIn The BoxQuick Guide (hard copy)Power CablePA-DSA832 Preamplifier OptionNIST calibration certificate for the DSA832E-TGManufacturer SpecsSpecifications are valid under the following conditions: the instrument is within the calibration period, is stored for at least two hours at 0°Cto 50 °C temperature, and is warmed up for 40 minutes. Unless otherwise noted, the specifications in this manual include the measurementuncertainty.Typical (typ.): characteristic performance, which 80 percent of the measurement results will meet at room temperature (approximately 25°C ).This data is not warranted and does not include the measurement uncertainty.Nominal (nom.): the expected mean or average performance or a designed attribute (such as the 50O connector). This data is not warrantedand is measured at room temperature (approximately 25°C ).Measured (meas.): an attribute measured during the design phase which can be compared to the expected performance, such as theamplitude drift variation with time. This data is not warranted and is measured at room temperature (approximately 25°C ).NOTE: All charts in this manual are the measurement results of multiple instruments at room temperature unless otherwise noted. Thespecifications (except the TG specifications) listed in this manual are those when the tracking generator is off.FrequencyFrequency DSA832EFrequency range9 kHz to 3.2 GHzFrequency resolution1 HzInternal Reference FrequencyReference frequency10 MHzAccuracy±[ (time since last calibration × aging rate) + temperature stability + calibration accuracy]Initial calibration accuracy<1 ppmTemperature stability0°C to 50°C , reference to 25°C<1 ppmAging rate<2 ppm/yearFrequency Readout AccuracyMarker resolutionspan/ (number of sweep points - 1)Marker uncertainty±(frequency indication × reference frequency accuracy + 1% × span + 10% × resolution bandwidth +marker resolution)Frequency CounterResolution1 Hz, 10 Hz, 100 Hz, 1 kHz, 10 kHz, 100 kHzUncertainty±(frequency indication × reference frequency accuracy + counter resolution)Frequency SpanRange0 Hz, 100 Hz to maximum frequency of instrumentUncertainty±span/ (number of sweep points - 1)SSB Phase Noise 20°C to 30°C , f c = 1 GHzCarrier offset10 kHz offset<-90 dBc/HzResidual FM 20°C to 30°C , RBW = VBW = 1 kHzResidual FM<20 Hz (nom.)Bandwidths Set "Auto SWT" to "Accy"Resolution bandwidth (-3 dB)10 Hz to 1 MHz, in 1-3-10 sequenceRBW uncertainty<5% (nom.)Resolution filter shape factor (60 dB : 3 dB<5 (nom.)Video bandwidth (-3 dB)1 Hz to 3 MHz, in 1-3-10 sequenceResolution bandwidth (-6 dB) (EMI-DSA800 option)200 Hz, 9 kHz, 120 kHzAmplitudeMeasurement RangeRangefc = 10 MHzDANL to +20 dBmMaximum Input LevelDC voltage50 VCW RF powerattenuation = 30 dB+20 dBm (100 mW)Max. damage level [1]+30 dBm (1 W)NOTE: [1] When f c = 10 MHz, input level > +25 dBm and PA is Off, the protection switch will be on.Displayed Average Noise Level (DANL) attenuation = 0 dB, RBW = VBW = 10 Hz, sample detector, trace average = 50,tracking generator off, 20°C to 30°C , input impendence = 50 ΩPA off9 kHz to 100 kHz<-110 dBm (typ.)100 kHz to 5 MHz<-122 dBm, <-125 dBm (typ.)5 MHz to 3.2 GHz<-127 dBm, <-130 dBm (typ.)PA on100 kHz to 1 MHz<-142 dBm (typ.)1 MHz to 5 MHz<-140 dBm, <-143 dBm (typ.)5 MHz to 3.2 GHz<-145 dBm, <-148 dBm (typ.)Level DisplayLogarithmic level axis1 dB to 200 dBLinear level axis0 to reference levelNumber of display points601Number of traces3 + math traceTrace detectorsnormal, positive-peak, negative-peak, sample, RMS, voltage averagequasi-peak (with EMI-DSA800 option)Trace functionsclear write, max hold, min hold, average, view, blankUnits of level axisdBm, dBmV, dBµV, nV, µV, mV, V, nW, µW, mW, WFrequency Response f c = 100 kHz, attenuation = 10 dB, relative to 50 MHz, 20°C to 30°CPA off100 kHz to 3.2 GHz<0.7 dB f c = 1MHz, attenuation = 10 dB, relative to 50 MHz, 20°C to 30°CPA on100 kHz to 3.2 GHz<1.0 dBInput Attenuation Switching UncertaintySetting range0 dB to 30 dB, in 1 dB stepSwitching uncertaintyf c = 50 MHz, relative to 10 dB, 20°C to 30°C<0.3 dBAbsolute Amplitude UncertaintyUncertaintyf c = 50 MHz, peak detector, preamplifier off, attenuation = 10 dB, input signal level = -10dBm, 20°C to 30°C<0.3 dBRBW Switching UncertaintyUncertaintyrelative to 1 kHz RBW<0.1 dBReference LevelRange-100 dBm to +20 dBm, in 1 dB stepResolutionlog scale0.01 dBlinear scale4 digitsPreamplifier PA-DSA832 (standard as of 4/1/2017)Gain100 kHz to 3.2 GHz17 dB (nom.)Level Measurement Uncertainty 95% confidence level, S/N > 20 dB, RBW = VBW = 1 kHz, preamplifier off, attenuation = 10 dB, -50 dBm <input level = 0 dBm, f c > 10 MHz, 20°C to 30°CLevel measurementuncertainty<1.0 dB (nom.)RF Input VSWR attenuation = 10 dBVSWR300 kHz to 3.2 GHz<1.5 (nom.)DistortionSecond Harmonic InterceptSecond harmonic intercept(SHI)f c = 50 MHz, input signal level = -20 dBm, attenuation = 10 dB+40 dBmThird-order InterceptThird-order intercept(TOI)f c = 50 MHz, two -20 dBm tones at input mixer spaced by 200 kHz, attenuation = 10 dB+7 dBm1dB Gain Compression1dB compression of inputmixer (P 1dB )f c = 50 MHz, attenuation = 0 dB>0 dBmSpurious ResponseSpurious response, inherentinput terminated 50 Ω, attenuation = 0 dB, 20°C to 30°C<-90 dBm [2] , <-100 dBm (typ.)Intermediate frequency<-60 dBcSystem related sidebandsreferenced to local oscillators, referenced to A/D conversion, referenced to subharmonic of first LO,referenced to harmonic of first LO<-60 dBcInput related spuriousmixer level = -30dBm<-60 dBcNOTE: [2] Except the internal local oscillator (1820 MHz) and its harmonics.SweepSweepSweep timespan = 100 Hz1 ms to 3200 szero span20 µs to 3200 sSweep time uncertaintyspan = 100 Hz5% (nom.)zero span (sweep time settingvalue > 1 ms)5% (nom.)Sweep modecontinuous, singleTracking Generator (Option)TG OutputFrequency range100 kHz to 3.2 GHzOutput level range-40 dBm to 0 dBmOutput level resolution1 dBOutput flatnessrelative to 50 MHz±3 dB (nom.)TriggerTriggerTrigger sourceTrigger sourceExternal trigger levelExternal trigger levelInput /OutputFront Panel ConnectorsRF inputimpedance50 Ω (nom.)connectorN femaleTracking generator outputimpedance50 Ω (nom.) <connectorN femaleInternal/ External ReferenceInternal referencefrequency10 MHzoutput level+3 dBm to +10 dBm, +8 dBm (typ.)impedance50 Ω (nom.)connectorBNC femaleExternal referencefrequency10 MHz ± 5 ppminput level0 dBm to +10 dBmimpedance50 Ω (nom.)connectorBNC femaleExternal Trigger InputExternal trigger inputimpedance1 kΩ (nom.)connectorBNC femaleCommunication InterfaceUSB hostconnectorA plugprotocolversion2.0USB deviceconnectorB plugprotocolversion2.0LANLXI core 2011 device10/100Base, RJ-45IEC/IEEE (GPIB) bus (USB-GPIB option)IEEE488.2General SpecificationDisplayTypeTFT LCDResolution800 x 480 pixelsSize8 inchColors64kPrinter SupportedProtocolPictBridgeMass MemoryMass memoryflash disk (internal),USB storage device (not supplied)Power SupplyInput voltage range, AC100 V to 240 V (nom.)AC supply frequency45 Hz to 440 HzPower consumption35 W (typ.), max. 50 W with all optionsEnvironmentalTemperatureoperating temperature range0°C to 50°Cstorage temperature range-20°C to 70°CHumidity0°C to 30°C= 95% rel. humidity30°C to 40°C= 75% rel. humidityAltitudeoperating heightup to 3,000mElectromagnetic Compatibility and SafetyEMCin line with EN61326-1:2006IEC 61000-4-2:2001±4.0 kV (contact discharge), ±4.0 kV (air discharge)IEC 61000-4-3:20023 V/m (80 MHz to 1 GHz), 3 V/m (1.4 GHz to 2 GHz), 1 V/m (2.0 GHzto 2.7 GHz)IEC 61000-4-4:20041 kV power linesIEC 61000-4-5:20010.5 kV (phase to neutral), 0.5 kV (phase to PE), 1 kV (neutral to PE)IEC 61000-4-6:20033 V, 0.15 to 80 MHzIEC 61000-4-11:2004voltage dip: 0% UT during half cycle, 0% UT during 1 cycle, 70% UTduring 25 cyclesshort interruption: 0% UT during 250 cyclesElectrical safetyin line withUL 61010-1:2012, CAN/CSA-C22.2 No. 61010-1-12, EN 61010-1:2010Dimensions(W x H x D)361.6 mm × 178.8 mm × 128 mm(14.2 in × 7.0 in × 5.0 in)WeightStandard4.55 kg (10.0 lb)With tracking generator5.15 kg (11.4 lb)Calibration IntervalRecommended calibration interval1 yearTech SpecsSpectrum Analyzers/Spectrum Analyzers TemplateBandwidth Range Max3.2 GhzBandwith Range Min9 kHzNoise Floor-158 dBm (-158 dB) Tracking GeneratorYesType(Spectrum Analyzers)BenchtopChannel Power MeasurementYesAuto tuningYesMarker MeasurementYesPreamplifierYesAM/FM DemodulationYesPower MeterNoTest Equipment General AttributesWarranty3 YEARSSafety ApprovalCEInterfaces I/OLAN / Ethernet, Other, USB Host, USBStorageInternal Memory, USB Flash DriveProduct Weight11.4 LBSProduct Height7 INProduct Length14.2 INProduct Width5 INShipping Weight15 LBSData LoggingNoHTS/Schedule B Number9030840000ECCN Number3A992.aCalibration IncludedFactory CalibrationPower Supply Voltage120V/220V UniversalCountry of OriginChinaShipping Height12 INShipping Length18 INShipping Width11 INAlat Laboratorium Umum