WEATHER STATION

Alat Uji Pengamat CuacaHOBO State/Pulse/Event/Runtime 128KOne logger with 4 recording modesInternal reed switch can be used to determine when a door or window is open or closedCompatible with a wide range of external sensorsShips with 2.5 mm input cableCompatible with HOBOware and HOBOware Pro software for logger setup, graphing and analysishe HOBO State/Pulse/Event/Runtime data logger records state changes,electronic pulses and mechanical or electrical contact closures from external sensing devices. This data logger is ideal for monitoring energy consumption, mechanical equipment operation, and water and gas flow. The HOBO UX90-001 State Data Logger is available in a standard 128 KB memory model (UX90-001) capable of 84,650 measurements and an expanded 512KB memory version (UX90-001M) capable of over 346,795 measurements.Environment:The UX90-001 Data Logger is for use in Indoor environments.Measurements:The UX90-001 Data Logger supports the following measurements:Event, Kilowatt Hours (kWh), Motor On/Off, Pulse Input, Runtime, State Open/Closed, Water Flow.Internal SensorMaximum State, Event, Runtime Frequency1 HzPreferred Switch StateNo magnet present (normally open)External InputExternal Contact InputElectronic solid state switch closure or logic driven voltage outputRange0 to 3 V DC (USB powered), 0 to 2.5 V DC (battery powered)Maximum Pulse Frequency50 HzMaximum State, Event, Runtime Frequency1 HzPulse, Event Lockout Time0 to 1 second in 100 ms stepsSolid State Switch ClosureInput Low: < 10 KOhms; Input High: > 500 KOhmsInternal Weak Pull-Up100 KOhmsInput ImpedanceSolid state switch closure: 100 KOhms pull upLoggerResolutionPulse: 1 pulse, Runtime: 1 second, State and Event: 1 State or EventLogging Rate1 second to 18 hours, 12 minutes, 15 secondsTime Accuracy±1 minute per month at 25°C (77°F) (see Plot A)Battery Life1 year, typical with logging intervals greater than 1 minute and normally open contactsMemoryUX90-001128 KB (84,650 measurements, maximum)UX90-001M512 KB (346,795 measurements, maximum)Download TypeUSB 2.0 interfaceDownload Time10 seconds for 128 KB; 30 seconds for 512 KBLogger Operating RangeLogging-20° to 70°C (-4° to 158°F); 0 to 95% RH (non-condensing)Launch/Readout0° to 50°C (32° to 122°F) per USB specificationLCDLCD is visible from: 0° to 50°C (32° to 122°F); the LCD may react slowly or go blank in temperatures outside this rangeSize3.66 x 5.94 x 1.52 cm (1.44 x 2.34 x 0.6 in.)Weight23 g (0.81 oz)Environmental RatingIP50 

Alat Uji Pengamat CuacaHOBO MicroRX station w/batteryHOBO MicroRX station w/batteryStation-side alarms for water flow and accumulated rainfall triggered at time of measurementNon-vented ceramic water level sensor with a choice of four rangesInterchangeable, Kevlar-reinforced water level sensor cablesIntegrated barometric pressure sensorCompact IP66/NEMA 4X enclosureBuilt-in LCD confirms proper setup and operationInputs for five plug-and-play smart sensorsUp to 10-minute connections rates via 4G cellular data plansCloud-based monitoring and data access through HOBOlinkHOBO by Onset MX2101 HOBO MicroRX Station with BatteryStation-side alarms for water flow and accumulated rainfall triggered at time of measurementNon-vented ceramic water level sensor with a choice of four rangesInterchangeable, Kevlar-reinforced water level sensor cablesIntegrated barometric pressure sensorThe HOBO MicroRX Water Level Station is a cellular, web-enabled water level monitoring solution for stormwater, floodwater, irrigation, hydrologic, and environmental applications. Pre-programmed water flow formulas for select weirs, flumes, and a stage discharge table result in an easy and intuitive configuration.New water flow and accumulated rainfall calculations, which are performed directly on the station at time of measurement, trigger immediate notifications of critical water level conditions.The compact and durable station, together with the non-vented water level sensor, enables harsh condition deployments and reliable monitoring. The optional integrated solar panel or battery power, with a wide range of plug-and-play smart sensors, supports flexible environmental monitoring.General SpecificationsOperating RangeRX2101 and RX2103: -40° to 60°C (-40° to 140°F)RX2102 and RX2104: -20° to 60°C (-4° to 140°F)Smart Sensor Connectors5Smart Sensor Network Cable Length100 m (328 ft) maximumSmart Sensor Data ChannelsMaximum of 15 (some smart sensors use more than one data channel; see sensor manual for details)Logging Rate1 minute to 18 hoursTime Accuracy±8 seconds per month in 0° to 40°C (32°F to 104°F) range;±30 seconds per month in -40° to 60°C (-40° to 140°F) rangeBattery Type/Power SourceRX2103: 6 AA 1.5 V lithium batteries or AC power adapter (P-AC-1)RX2104: Integrated 1.7 watt solar panel and NiMH rechargeable battery pack; optional AC power adapter (P-AC-1) or external solar panel (SOLAR-xW) can be used in place of integrated solar panelBattery LifeRX2103 Battery Life:Battery life with daily connections:RX2103: 1 year with 2 minute loggingBattery life with hourly connections and 1 minute logging:RX2103: 2 monthsNote: Deployments in areas with weak cellular strength could reduce battery life. RX2104 Battery Life:Typical 3–5 years when operated in the temperature range -20° to 40°C (-4° to 104°F); operation outside this range will reduce the battery service life.Maximum connection rates with built-in solar panel, in full sun:10 minute connections year round for latitudes less than ±40°10 minute connections through three seasons in other regions, reduced to 30 minute connections in winterMaximum connection rates with external 5W or 15W solar panels:10 minute connections year round, in full sunConnection rate with external solar panels may be less if deployed in partial sunBattery life without solar recharging, with hourly connections and1 minute logging:RX2104: 2 monthsMemory16 MB, 1 million measurements, continuous loggingAlarm Notification LatencyLogging interval plus 2–4 minutes, typicalEnclosure AccessHinged door secured by two latches with eyelets for use with user-supplied padlocksLCDLCD is visible from 0° to 50°C (32° to 122°F); the LCD may react slowly or go blank in temperatures outside this rangeMaterialsOuter enclosure: Polycarbonate/PBT blend with brass inserts; Interior: Polycarbonate/PBT; Gasket: Silicone foam; Cable channel: Santoprene™ TPE; U-Bolts (not included): Steel with zinc dichromate finishDimensions19.95 x 13.68 x 7.49 cm (7.85 x 5.39 x 2.95 in.)Weight678 g (23.9 oz)MountingOptional U-bolts are compatible with masts up to 4.14 cm (1.63 in.) mast diameter; can also be mounted with zip ties or mounted to a flat surface with screwsEnvironmental RatingWeatherproof enclosure, NEMA 4X and IP66 (requires proper installation of cable channel system)Wireless RadioGSM/GPRS/EDGE: Quad band 850/900/1800/1900 MHzUMTS/HSPA+: Seven band 800/850/900/1800/1900/2100 MHzLTE: Twelve Band 700/800/850/900/1800/1900/2100/2600 MHzAntenna4G LTEWater Level Sensor:Operation Range0 to 207 kPa (0 to 30 psia); approximately 0 to 9 m (0 to 30 ft) of water depth at sea level, or 0 to 12 m (0 to 40 ft) of water at 3,000 m (10,000 ft) of altitudeFactory Calibrated Range69 to 207 kPa (10 to 30 psia), 0° to 40°C (32° to 104°F)Burst Pressure500 kPa (72.5 psia) or 40.8 m (134 ft) depthWater Level Accuracy*Typical error: ±0.05% FS, 1.5 cm (0.05 ft) waterMaximum error: ±0.1% FS, 3.0 cm (0.01 ft) waterRaw Pressure Accuracy**±0.3% FS, 1.20 kPa (0.17 psi) maximum errorResolution< 0.04 kPa (0.006 psi), 0.41 cm (0.013 ft) waterPressure Response Time (90%)***< 1 second at a stable temperaturePressure (Absolute) And Water Level Measurements MX2001-03-S:Operation Range0 to 850 kPa (0 to 123.3 psia); approximately 0 to 76.5 m (0 to 251 ft) of water depth at sea level, or 0 to 79.5 m (0 to 262 ft) of water at 3,000 m (10,000 ft) of altitudeFactory Calibrated Range69 to 850 kPa (10 to 123.3 psia), 0° to 40°C (32° to 104°F)Burst Pressure1,200 kPa (174 psia) or 112 m (368 ft) depthWater Level Accuracy*Typical error: ±0.05% FS, 3.8 cm (0.125 ft) waterMaximum error: ±0.1% FS, 7.6 cm (0.25 ft) waterRaw Pressure Accuracy**±0.3% FS, 2.55 kPa (0.37 psi) maximum errorResolution< 0.085 kPa (0.012 psi), 0.87 cm (0.028 ft) waterPressure Response Time (90%)***< 1 second at a stable temperaturePressure (Absolute) And Water Level Measurements MX2001-04-S and MX2001-04-Ti-S:Operation Range0 to 145 kPa (0 to 21 psia); approximately 0 to 4 m (0 to 13 ft) of water depth at sea level, or 0 to 7 m (0 to 23 ft) of water at 3,000 m (10,000 ft) of altitudeFactory Calibrated Range69 to 145 kPa (10 to 21 psia), 0° to 40°C (32° to 104°F)Burst Pressure310 kPa (45 psia) or 18 m (60 ft) depthWater Level Accuracy*Typical error: ±0.075% FS, 0.3 cm (0.01 ft) waterMaximum error: ±0.15% FS, 0.6 cm (0.02 ft) waterRaw Pressure Accuracy**±0.3% FS, 0.43 kPa (0.63 psi) maximum errorResolution< 0.014 kPa (0.002 psi), 0.14 cm (0.005 ft) waterPressure Response Time (90%)***< 1 second at a stable temperatureBarometric Pressure (RX2103 and RX2104 station):Operation Range66 to 107 kPa (9.57 to 15.52 psia)Temperature Calibrated Range-20 to 50°C (-4 to 122°C)Accuracy±0.2 kPa (±0.029 psi) over full temperature range at fixed pressure; maximum error ±0.5% FSWater Level Accuracy*Typical error: ±0.075% FS, 0.3 cm (0.01 ft) waterMaximum error: ±0.15% FS, 0.6 cm (0.02 ft) waterResolution< 0.01 kPa (0.0015 psi)Response Time< 1 second at a stable temperatureStability (Drift)0.1°C (0.18°F) per yearTemperature (Water Level Sensors MX2001-0x-S and MX2001-0x-Ti-S):Operation Range-20° to 50°C (-4° to 122°F)Accuracy±0.44°C from 0° to 50°C (±0.79°F from 32° to 122°F)Resolution0.1°C at 25°C (0.18°F at 77°F)Response Time (90%)5 minutes in water (typical)Stability (Drift)0.1°C (0.18°F) per year* Water Level Accuracy: With accurate reference water level measurement, known water density, and a stable temperature environment. System Water Level Accuracy equals the sum of the Barometric Water Level Accuracy plus the selected sensor Water Level Accuracy.** Raw Pressure Accuracy: Absolute pressure sensor accuracy includes all sensor drift, temperature, and hysteresis-induced errors.*** Changes in Temperature: Allow 20 minutes in water to achieve full temperature compensation of the pressure sensor. There can be up to 0.5% of additional error due to rapid temperature changes.Measurement accuracy also depends on temperature response time. 

Alat Uji Pengamat CuacaHOBO UX100 TempEasy-to view LCD displayLarge memory capacityVisual high & low alarm thresholdsNew Burst and Statistics logging modesCompatible with HOBOware and HOBOware Pro software for logger setup, graphing and analysisThe HOBO UX100-001 Temperature data logger records temperature in indoor environments with its integrated sensor. The logger is ideal for monitoring occupant comfort in office buildings, tracking food storage conditions in warehouses, and logging temperature trends in server rooms.Environment:The UX100-001 Data Logger is for use in Indoor environments.Measurements:The UX100-001 Data Logger supports the following measurements:Temperature.emperature SensorRange-20° to 70°C (-4° to 158°F)Accuracy±0.21°C from 0° to 50°C (±0.38°F from 32° to 122°F), see Plot AResolution0.024°C at 25°C (0.04°F at 77°F); see Plot AResponse Time8 minutes in air moving 1 m/s (2.2 mph)Drift<0.1°C (0.18°F) per yearLoggerLogger Operating RangeLogging-20° to 70°C (-4° to 158°F); 0 to 95% RH (non-condensing)Launch/Readout0° to 50°C (32° to 122°F) per USB specificationLogging Rate1 second to 18 hours, 12 minutes, 15 secondsLogging ModesNormal, Burst or StatisticsMemory ModesWrap when Full or Stop when FullStart ModesImmediately, Push Button, Date & Time or Next IntervalStop ModesWhen Memory Full, Push Button, or Date & TimeRestart ModePush ButtonTime Accuracy±1 minute per month at 25°C (77°F), see Plot BBattery Life1 year, typical with logging rate of 1 minute and sampling interval of 15 seconds or greaterMemory128 KB (84,650 measurements, maximum)Download TypeUSB 2.0 interfaceFull Memory Download Time20 secondsLCDLCD is visible from: 0° to 50°C (32° to 122°F); the LCD may react slowly or go blank in temperatures outside this rangeSize3.66 x 5.94 x 1.52 cm (1.44 x 2.34 x 0.6 in.)Weight23 g (0.81 oz)Environmental RatingIP50 

Alat Uji Pengamat CuacaHOBO UX100 ThermocoupleHigh-accuracy J, K, T, E, R, S, B, N thermocouple readingsEasy-to view LCD displayLarge memory capacityVisual high & low alarm thresholdsNew Burst and Statistics logging modesRecord ambiant temperature with internal thermistorEnvironment:The UX100-014M Data Logger is for use in Indoor environmentsMeasurements:The UX100-014M Data Logger supports the following measurements (sensors sold separately):TemperatureThe HOBO UX100-014M Single Channel Thermocouple data logger records temperature in indoor environments with thermocouple sensors (sold separately). Designed for a broad range of monitoring applications – from industrial process monitoring to concrete maturity testing – the logger provides exceptional flexibility by accepting J, K, T, E, R, S, B or N type thermocouple probes.IMPORTANT: This HOBO data logger requires HOBOware software and a communications device. Internal 10K Thermistor (Temperature)RangeLogging: -20° to 70°C (-4° to 158°F)Accuracy±0.21°C from 0° to 50°C (±0.38°F from 32° to 122°F)Resolution0.024°C at 25°C (0.04°F at 77°F)Drift<0.1°C (0.18°F) per yearLoggerLogger Operating RangeLogging: -20° to 70°C (-4° to 158°F); 0 to 95% RH (non-condensing);logger accuracy from 0° to 50°C (32° to 122°F)Launch/Readout: 0° to 50°C (32° to 122°F) per USB specificationResolution22-bitLogging Rate1 second to 18 hours, 12 minutes, 15 secondsLogging ModesNormal, Burst or StatisticsMemory ModesWrap when Full or Stop when FullStart ModesImmediately, Push Button, Date & Time or Next IntervalStop ModesWhen Memory Full, Push Button, or Date & TimeRestart ModePush ButtonTime Accuracy±1 minute per month at 25°C (77°F)Battery Life1 year, typical with logging rate of 1 minute and sampling interval of 15 seconds or greaterBattery TypeOne 3V CR2032 lithium batteryMemory512 KB (208,076 measurements, maximum)Download TypeUSB 2.0 interfaceFull Memory Download Time1 minute, 30 secondsLCDLCD is visible from: 0° to 50°C (32° to 122°F); the LCD may react slowly or go blank in temperatures outside this rangeSize3.66 x 5.94 x 1.52 cm (1.44 x 2.34 x 0.6 in.)Weight30 g (1.06 oz)Environmental RatingIP50 

Alat Uji Pengamat CuacaHOBO MX2300 tempTemperature Data LoggerWeatherproof housing for use in outdoor or condensing environmentsHigh-accuracy measurementsRH sensor provides superior recovery from condensing conditionsSmall-diameter, external sensor versions for measurements in tight spacesWireless setup & download with Bluetooth Low Energy (BLE)Convenient wireless setup and download via Bluetooth Low Energy (100-foot range)Retrieve data in hard-to-reach locationsVisual alarms alert you to out-of-range conditionsCompact, weatherproof housing with built-in mountingemperature Data LoggerConvenient wireless setup and download via Bluetooth Low Energy (100-foot range)Retrieve data in hard-to-reach locationsVisual alarms alert you to out-of-range conditionsCompact, weatherproof housing with built-in mountingView current data in real time with Onset’s free HOBO mobile appThe HOBO MX2305 is a weatherproof data logger with built-in temperature and relative humidity sensors. Leveraging Bluetooth Low Energy, the logger enables easy, fast set up and data download directly from your mobile device, and provides high-accuracy measurements in harsh outdoor environments.With Onset's new HOBO MX2300 Series Temp/ RH loggers, field data collection has never been easier. You can set up and offload loggers wirelessly from your mobile device eliminating the need to take a laptop or data shuttle into the field to retrieve data.The HOBO MX2300 series data loggers record and transmit temperature and/or relative humidity (RH) in outdoor or indoor environments. These Bluetooth® Low Energy-enabled loggers are designed for wireless communication with a mobile device. Using the HOBOmobile® app, you can easily configure the logger, read it out, and view data on your phone or tablet, or export the data for further analysis. The logger can calculate minimum, maximum, average, and standard deviation statistics and be configured to indicate alarms at thresholds you specify. The logger also supports burst logging in which data is logged at a faster interval when sensor readings are above or below certain limits. The Temp and Temp/RH models have internal sensors while the External Temp /RH, External Temp, and 2x Ex ternal Temp include built-in external sensors, offering a wide range of so lutions for monitoring temperature and RH in numerous applications. Temperature SensorsRange-40 to 70°C (-40 to 158°F)-40 to 100°C (-40 to 212°F) with tip and cable immersion in fresh water up to 50°C (122°F) for one year-40 to 70°C (-40 to 158°F)Accuracy±0.25°C from -40 to 0°C (±0.45 from -40 to 32°F)±0.2°C from 0 to 70°C (±0.36 from 32 to 158°F)±0.25°C from 70 to 100°C (±0.45 from 158 to 212°F), MX2303 and MX2304 onlyResolution0.04°C (0.072°F)Drift<0.01°C (0.018°F) per year Relative Humidity Sensor (MX2301, MX2302 only)Range0 to 100% RH, -40° to 70°C (-40° to 158°F); exposure to conditions below -20°C (-4°F) or above 95% RH may temporarily increase the maximum RH sensor error by an additional 1%Accuracy±2.5% from 10% to 90% (typical) to a maximum of ±3.5% including hysteresis at 25°C (77°F); below 10% RH and above 90% RH: ±5% typicalResolution0.05%Drift<1% per year typical LoggerOperating Range-40° to 70°C (-40° to 158°F)Radio Power1 mW (0 dBm)Transmission RangeApproximately 30.5 m (100 ft) line-of-sightWireless Data StandardBluetooth Low Energy (Bluetooth Smart)Logging Rate1 second to 18 hoursLogging ModesFixed interval (normal, statistics) or burstMemory ModesWrap when full or stop when fullStart ModesImmediate, push button, date & time, or next intervalStop ModesWhen memory full, push button, date & time, or after a set logging periodTime Accuracy±1 minute per month 0° to 50°C (32° to 122°F)Battery Type2/3 AA 3.6 Volt lithium, user replaceable Battery Life 2 years, typical with logging interval of 1 minute and Power Saving Mode disabled; 5 years, typical with logging interval of 1 minute and Power Saving Mode enabled. Faster logging intervals and statistics sampling intervals, burst logging, remaining connected with the app, excessive downloads, and pagi ng may impact battery life.Memory128 KB (84,650 measurements, maximum)Full Memory Download TimeApproximately 60 seconds; may take longer the further the device is from the loggerDimensionsLogger housing: 10.8 x 5.08 x 2.24 cm (4.25 x 2.0 x 0.88 in.)External temperature sensor diameter: 0.53 cm (0.21 in.)External temperature/RH sensor diameter: 1.17 cm (0.46 in.)External sensor cable length: 2 m (6.56 ft)Solar radiation shield bracket: 10.8 x 8.3 cm (4.25 X 3.25 in.)WeightLogger: 75.5 g (2.66 oz)Solar radiation shield bracket: 20.4 g (0.72 oz)MaterialsAcetal, silicone gasket, stainless steel screwsEnvironmental RatingNEMA 6 and IP67 Temperature Without SolarRadiation ShieldWith RS1/M-RSASoalr Radiation ShieldWith RS3-BSolar Radiation ShieldMX2301 Internal sensor17 minutes in air moving 1 m/sec24 minutes in air moving 1 m/secN/AMX2302 Internal sensor2 minutes, 30 seconds in air moving 1 m/sec6 minutes in air moving 1 m/sec5 minutes in air moving 1 m/secMX2303 Internal sensor3 minutes in air moving 1 m/sec; 20 seconds in stirred water7 minutes in air moving 1 m/sec4 minutes in air moving 1 m/secMX2304 Internal sensor3 minutes in air moving 1 m/sec; 20 seconds in stirred water7 minutes in air moving 1 m/sec4 minutes in air moving 1 m/secMX2305 Internal sensor17 minutes in air moving 1 m/sec24 minutes in air moving 1 m/secN/ARH Without SolarRadiation ShieldWith RS1/M-RSASoalr Radiation ShieldWith RS3-BSolar Radiation ShieldMX2301 Internal sensor1 minute in air moving 1 m/sec1 minute in air moving 1 m/secN/AMX2302 Internal sensor4 minutes in air moving 1 m/sec4 minutes in air moving 1 m/sec4 minutes in air moving 1 m/sec 

Alat Uji Pengamat CuacaHOBO U30 ShuttleReads out data from systems in the field for transfer to a host computerOptionally relaunches the data logger — synchronizes the logger’s clock with the shuttle’s clock and (in most cases) sets logging to begin at the next intervalPreserves data in nonvolatile memory, even if batteries are depletedDisplays logger status, including memory, battery level, and sensor readingsDisplays its own status, including clock, memory, and battery levelLets you change the batteries in the field without resetting the clockAllows you to test individual smart sensorsEnvironment:The HOBO U-DT-2 U30 Shuttle Data Transporter provides convenient in-field data offload and relaunch of HOBO U30-NRC systems and HOBO Weather Stations (H21), Micro Stations, and HOBO Energy Logger systems (H22). The U30 Shuttle's 2 x 16-character display shows current readings (for selected data loggers), and logger status.RequirementsUSB cable (provided); compatible logger with appropriate cable and/or base stationU-DT-2: HOBOware 2.6 or greaterCompatibilityHOBO U30 series systems, HOBO Weather Stations and Micro Stations (H21), and HOBO Energy Logger (H22)Firmware upgradesOperating temperature0° to 50°C (32° to 122°F)Storage temperature-10° to 50°C (14° to 122°F)Time accuracy± 1 minute per month at 25°C (77°F); see Plot ALogger-to-shuttle transfer speedUSB 64K in approximately 30 secondsSerial: 512K in approximately 60 secondsShuttle-to-host transfer speedFull shuttle offload (4 MB) to host computer in 3 to 5 minutes, depending on computerData capacity (full loggers)4 MB (minus 64 KB for shuttle information): enough for 7 readouts of 512K loggersIdle timeoutShuttle powers down after two minutes of idle time, except when actively communicating with HOBOware or changing logger batteries (10 minutes)PortsRJ-12 jack for communicating with smart sensors; mini-B full speed USB port for communicating with host computer; full speed USB port for communicating with U-Series loggers and base stations; high speed serial port for communicating with serial loggers. Shuttle communicates with only one device at a timeBatteriesMain2 AA alkaline batteriesClock backup1 CR1225 lithium battery (3 V)Battery lifeMainOne year or approximately 50 complete memory fills, typical useClock backup10 years typical use (with main batteries installed)Weight153 g (5.4 oz)Dimensions11.0 x 6.9 x 2.7 cm (4.35 x 2.70 x 1.05 inches)Case materialsABS case with urethane rubber grips, polycarbonate label 

Alat Uji Pengamat CuacaHOBO Waterproof ShuttleReads out all logger information (serial number, deployment number, data, etc.) from loggers in the field for transfer to host computer, and stores each logger’s data in a “bank”Nonvolatile memory preserves data, even if batteries are depletedRelaunches the logger, resetting the logger’s time to the shuttle’s time and synchronizing the logging interval on relaunchCan be used as an optic-to-USB base stationThe HOBO Waterproof Shuttle provides convenient readout and relaunching of underwater and outdoor HOBO data loggers with an Optic USB interface, and is waterproof to 20m (66ft). The HOBO Waterproof Shuttle can also be used as a base station.NOTE: Couplers are included for compatibility with five of our most popular logger types including: UA Pendants, U20 water level data loggers, the U22 Water Temp Pro v2, our UTBI TidbiT, U24 Conductivity and U23 data loggers.NOTE: HOBOware Pro software required. Onset offers a range of data retrieval and communications options to make data offload from HOBO data loggers fast and easy.CompatibilityAll HOBO U-Series loggers with optic USBNot compatible with the HOBO U-Shuttle (U-DT-1)RequirementsHOBOware 2.2+Compatible logger and matching coupler- For UA Pendant (Part # COUPLER2-A)- For U20 Water Level (Part # COUPLER2-B)- For U22 Water Temp Pro v2 (Part # COUPLER2-C)- For UTBI TidbiT v2 (Part # COUPLER2-D)- For U23 HOBO Pro v2 (Part # COUPLER2-E)Data capacity63 logger readouts of up to 64K eachOperating temperature0° to 50°C (32° to 122°F)Storage temperature-20° to 50°C (-4° to 122°F)Wetted materialsPolycarbonate case, EPDM o-rings and retaining loopWaterproofTo 20 m (66 feet)Time accuracy± 1 minute per month at 25°C (77°F)Logger-to-shuttle transfer speedReads out one full 64K logger in about 30 secondsShuttle-to-host transfer speedFull shuttle offload (4 MB) to host computer in 10 to 20 minutes, depending on computerBatteries2 AA alkaline batteries required for remote operationBattery lifeOne year or at least 50 complete memory fills, typical useWeight150 g (4 oz)Dimensions15.2 x 4.8 cm (6.0 x 1.9 inches) 

Alat Uji Pengamat CuacaHOBO U-ShuttleReads out data from loggers in the field for transfer to a host computerOptionally relaunches the logger—synchronizes the logger’s clock with the shuttle’s clock and (in most cases) sets logging to begin at the next intervalPreserves data in nonvolatile memory, even if batteries are depletedDisplays logger status, including memory, battery level, and sensor readings for some sensors (on some models)Displays its own status, including clock, memory, and battery levelLets you change the batteries in the field without resetting the clockAllows you to test individual smart sensors (does not support the TRMSA-D) Conveniently offload data in the field with the HOBO U-Shuttle Data Transporter. This product also allows users to easily relaunch HOBO U-series data loggers and HOBO Weather Stations, Micro Stations, and HOBO Energy Logger systems. View readings on a 2 x 16-character display for selected data loggers, and access logger status for all loggers. An Optic USB Base Station is required for use with optic USB data loggers.The U-DT-1 is compatible with all U-Series loggers (except the HOBO U30 Station), all UX-Series loggers, HOBO Weather Stations and Micro Stations (H21), and the HOBO Energy Logger (H22). The U-DT-2 is compatible with the HOBO U30 Station, HOBO Weather Stations and Micro Stations (H21), and HOBO Energy Logger (H22).NOTE: HOBOware Pro software requiredOnset offers a range of data retrieval and communications options to make data offload from HOBO data loggers fast and easy.RequirementsHOBOware Pro 2.2.0 or greater; USB cable (provided)Compatible logger with appropriate cable and/or base stationCompatibilityAll U-Series loggers, HOBO Weather Stations and Micro Stations (H21), and HOBO FlexSmart loggers (H22); not compatible with the HOBO Waterproof Shuttle (U-DTW-1)Firmware upgradesAvailable on the Onset website as needed to provide compatibility with future supported logger modelsOperating temperature0° to 50°C (32° to 122°F)Storage temperature-10° to 50°C (14° to 122°F)Time accuracy± 1 minute per month at 25°C (77°F); see Plot ALogger-to-shuttle transfer speedUSB/optic64K in approximately 30 secondsSerial512K in approximately 60 secondsShuttle-to-host transfer speedFull shuttle offload (4 MB) to host computer in 3 to 5 minutes, depending on computerData capacity (full loggers)4 MB (minus 64 KB for shuttle information): enough for 504 readouts of 8K loggers, 63 readouts of 64K loggers, or 7 readouts of 512K loggersIdle timeoutShuttle powers down after two minutes of idle time, except when actively communicating with HOBOware or changing logger batteries (10 minutes)PortsRJ-12 jack for communicating with smart sensorsMini-B full speed USB port for communicating with host computerFull speed USB port for communicating with U-Series loggers and base stationsHigh speed serial port for communicating with serial loggersShuttle communicates with only one device at a timeBatteries Main2 AA alkaline batteriesClock backup1 CR1225 lithium battery (3 V)Battery life MainOne year or approximately 50 complete memory fills, typical useClock backup10 years typical use (with main batteries installed)Weight153 g (5.4 oz)Dimensions11.0 x 6.9 x 2.7 cm (4.35 x 2.70 x 1.05 inches)Case materialsABS case with urethane rubber grips, polycarbonate label 

Alat Uji Pengamat CuacaHOBO data routerSimple, cost-effective solution for transmitting data from HOBO data nodes that are too far away from the receiver or whose signal is blocked by an obstruction or interferencesAutomatically determines the best path to deliver node data back to the receiverImproves the reliability and redundancy of data node networksEnvironment:The ZW-ROUTER is for use in Indoor environmentsThe HOBO®data router routes data from networked HOBO data nodes to ensure that the data is transmitted back to the receiver. PowerAC Adapter.RangeApprox. 100 m (300 ft.) depending on obstructions or interferenceWeight138 g (4.87 oz.) w/ batteriesSize96.5 x 108 x 28 mm (3.8 x 4.25 x 1.1 in.)Operating RangeTemp-20 to 50°C (-4 to 122°F) when battery powered, -20 to 70°C (-4 to 158°F) when line powered.RH5%-95% non-condensingRadio power1.6 mW (2 dBm)Wireless data standardIEEE 802.15.4 2.4 GHz bandCEThe CE Marking identifies this product as complying with all relevant directives in the European Union (EU) 

Alat Uji Pengamat CuacaHOBO Energy LoggerOnset's most flexible data logger records up to 15 channels of over a dozen measurementsProvides 12v excitation for third-party sensorsPre-configured smart sensors get you started fastSignal conditioning modules retain configurations until you change them, providing plug-and-play convenience for commonly used sensorsFlexible power options include battery operation for AC power adapterHOBO H22-001 Energy Data LoggerMonitor energy and industrial equipment with this 15-channel data logger. With multiple channels, energy and facility managers can quickly and easily detect and address a variety of issues relating to HVAC, machinery, and other systems.  The HOBO Energy Data Logger is modular and more economic than its alternatives because a toolbox full of data loggers is not necessary.Deploy this product with a variety of pre-defined plug-and-play smart sensors to create a robust monitoring system. Compatible with HOBOware® software, researchers can conduct effective data analysis in minutes.Environment:The H22-001 Data Logger is for use in Indoor environmentsMeasurements:The H22-001 Data Logger supports the following measurements (sensors sold separately):4-20mA, AC Current, AC Voltage, Air Velocity, Amp Hour (Ah), Carbon Dioxide, Compressed Air Flow, DC Current, DC Voltage, Differential Pressure, Gauge Pressure, Kilowatt Hours (kWh), Kilowatts (kW), Power Factor (PF), Pulse Input, Relative Humidity, Temperature, Volatile Organic Comp., Volt-Amp Reactive, Volt-Amp Reactive hour, Volt-Amps (VA), Water Flow, Watt Hours (Wh), Watts (W), Wind. HOBO H22-001 Energy Data Logger SpecificationsOperating range-20° to 50°C (-4° to 122°F) with alkaline batteries-40° to 60°C (-40° to 140°F) with lithium batteriesSensor inputsThree FlexSmart multi-channel modules and up to 6 Smart Sensors (which may have multiple parameters/channels)Sensor connectorsSix RJ-12 Smart Sensor jacks plus 3 FlexSmart module slotsCommunicationRS-232 via 3.5 mm serial port or/and 9-pin D-Sub connectorDimensions15.6 cm x 8.4 cm x 4.6 cm (6.13" x 3.31" x 1.81")Weight435 g (15.23 oz) with batteries 238 g (8.33 oz) without batteriesMemory512K nonvolatile flash data storageMemory modesStop when full; wrap when fullOperational indicatorsSix indicators provide logging and sensor network statusLogging intervalOne second to 18 hours, user-specified interval (2-second minimum for two-channel S-FS-TRMSA operation)Sensor excitation12 V DC at 200 mA total, with user-programmable warmup time on a per-channel basisBattery lifeOne year typical use (up to 75 mA excitation with 10-minute or longer logging Interval and 1-second warmup time)Battery typeEight standard AA alkaline batteries included (for operating conditions -20°C/-4°F to 50°C/122°F); optional AA lithium batteries available for operating conditions of -40° to 60°C (-40° to 140°F).External powerSupports optional 13.6 V DC regulated AC Wall Adapter Connector. Internal batteries may remain installed. Alternatively, an automotive battery or 9-12 V DC regulated Wall Adapter may be used, but it is recommended to remove the internal batteries since they will discharge to the level of the external supply.Time accuracy0 to 2 seconds for the first data point and ±5 seconds per week at 25°C (77°F)Logging modeImmediate, timed delay, or trigger (button-push) start options; supports sampling intervals for some sensorsData communicationCurrent readings while logging; read out while logging; read out when stopped