Amprobe AT-6030 Advanced Wire Tracer Kit
SKU:4867996
·Traces wiresin walls, ceilings, floors and corners
·Locatesbreakers and fuses
·Pinpointsshorts and opens
·Highresolution 2.5″ TFT LCD color display
·ThreeTransmitter signal modes
·“HighSignal” mode for normal circuits
·“Low Signal”mode for precision tracing in difficult areas
·“Loop” modefor closed loop de-energized circuits
·FourReceiver tracing modes
·“Quick Scan”mode allows for quick wire detection at a longer distance
·“Precision”mode precisely pinpoints wires or faults located behind walls, floors, or ceilings
·“BreakerIdentification” mode facilitates quick and easy breaker locating
·“Non-ContactVoltage Detection” mode utilizes passive tracing without the Transmitter to verify if a wire is energized
·Twoautomatically selected frequency modes for reliable tracing on energized and de-energized circuits
·Comes withcustom Amprobe hard carrying case, test leads, CT-400 signal clamp, and accessories
·Compatiblewith optional TIC 410A Hot Stick attachment to extend your reach
Specifications
AT-6000-R Receiver |
AT-6000-T Transmitter |
CT-400 Signal Clamp |
|
Measurement Category |
CAT III 600 V |
CAT III 600 V |
CAT IV 600 V, CAT III 1000 V |
Operating voltage |
0 to 600 V AC/DC |
0 to 600 V AC/DC |
0 to 1000 V AC |
Operating frequency |
Energized: 6.25 kHz De-Energized: 32.768 kHz |
Energized: 6.25 kHz De-Energized: 32.768 kHz |
Wire tracing: 32.768 kHz AC current measurement: 45 Hz to 400 Hz |
Hazardous voltage detection |
See NCV detection |
> 30 V AC/DC |
N/A |
Signal indications |
Numeric, bar graph display and audible beep |
LEDs and audible beep |
N/A |
Response time |
Tip Sensor (energized/de-energized): 500 MS NCV: 500 MS Battery voltage monitoring: 5 sec |
Line voltage monitoring: 1 sec Battery voltage monitoring: 5 sec |
Instantaneous |
Current output of signal (typical) |
N/A |
Energized circuit: HI mode: 60 mA RMS LO mode: 30 mA RMS De-energized circuit: HI mode: 130 mA RMS LO mode: 40 mA RMS Loop mode: 160 mA RMS |
1 mA/A for AC current measurement with multimeter |
Signal voltage output (nominal) |
N/A |
De-energized circuit: LOW: 29 V RMS, 120 Vp-p HIGH: 33V RMS, 140 Vp-p With CT-400: loop model: 31 V RMS, 120 Vp-p |
De-energized circuit: 2.4 V RMS, 24 Vp-p |
Range detection (open air) |
Tip sensor (Energized): Max distance via air: up to 20 ft (6.1 m) Pinpointing: approx. 1.97 in (5 cm) Tip sensor (De-energized): Max distance via air: up to 14.7 ft (4.5 m) Pinpointing: approx. 1.97 in (5 cm) NCV detection (40 to 400 Hz): Max. sensitivity: 90 V up to 6.56 ft (2 m) Min. sensitivity: 600 V up to 0.39 in (1 cm) |
N/A |
|
What’s Included
|
AT-6020 kit | AT-6030 kit |
AT-6000-R Receiver |
• | • |
AT-6000-T Transmitter |
• |
• |
TL-6000 Test Lead and Accessory Kit |
• | • |
CC-6000 Hard Carrying Case |
• |
• |
User Manual |
• | • |
1.5 V AA (IEC R6) Batteries (12) (not installed) |
• |
– |
Rechargeable Batteries (12) (not installed) |
– | • |
Battery Chargers (3) |
– |
• |
CT-400 Signal Clamp |
– | • |
Alat Laboratorium Umum